Logging in to the USG through the console interface

64

Perform the following operations to log in to the USG through the console interface:
1. Use the Windows XP HyperTerminal of a PC to log in to the USG through a console interface to manage the device.
By default, the authentication mode for the login to the USG through the console interface is AAA. The user name is admin, and the password is Admin@123.
Note:
If you fail to log in for consecutively three times, the system automatically locks the web UI for 10 minutes.
Procedure:
a. Connect desired devices, power on them, and ensure that they run properly.
b. Choose Start > All Programs > Accessories > Communication > HyerTerminal to start the terminal simulation program (for example, Windows XP HyerTerminal) on the PC. The Connection Description dialog box is displayed.
c. In Name, enter the name of the connection between the PC and the USG, for example, COMM1. Select any of the icons.
d. Click OK. The Connect To dialog box is displayed.
e. From the Connect using drop-down list, select the serial port connecting the PC to the USG, such as, COM1.
f. Click OK. The COM1 Properties dialog box is displayed.
g: Set the communication parameters of the interface.
Note:
The communications parameters of the terminal port must be consistent with those of the console port of the USG. Set the baudrate to 9600 bit/s. Other communication parameters adopt their default values.
h. Click OK or Restore to default value (R).
i. Proceed to the emulation program page, and press Enter. According to the authentication mode configured on the USG, enter the user name and password as prompted. The user view is displayed.
The default user name is admin, and the default password is Admin@123.

2. Log in to the CLI through the console port based on the PuTTY.
Before logging in to the CLI through the console port, connect a PC to the console port on the NGFW Module through a console cable.
Procedure:
a. Configure the PC. The following example describes the configuration using the free HyperTerminal software PuTTY on Windows 7.
b. Download the PuTTY software to the PC and double-click it to run the software.
c. Select Session and set Connection type to Serial.
d. After setting other parameters, click Open.
e. Press Enter and enter the default administrator account admin and password Admin@123.
Note:
After three consecutive login failures, the system automatically locks out the account (prohibiting its login) for 10 minutes.
f. Change the password of the default administrator account and enter the CLI.
Note:
For security, the password must meet the minimum complexity requirement. That is, the password must contain three of the following, including upper-case letters (A to Z), lower-case letters (a to z), digits (0 to 9), and special characters (such as !, @, #, $, and %).
Remember the new password for future logins.

Other related questions:
Logging in to the AR through a console interface
You can connect a PC to the console interface of an AR and then log in to the AR to perform basic configurations and management.

Log in to the S1700 through the console port
The S1700 series include the web-managed model and NMS-free model, and cannot be logged in to through the console port. The S1724G series and S1728GWR-4P series switches do not support console port login either.

Why do I fail to log in to the AR through the console interface
Use the following method:
1. Check whether parameter settings on the console interface are correct.
   - Baud rate: 9600
   - Data bit: 8
   - Stop bit: 1
   - Parity check: none
   - Flow control: none
2. Check whether the console cable is securely connected. If necessary, replace the current cable with a new one to check whether the cable is faulty.   
3.  By default, no flow control mode is configured on an AR. Because RTS/CTS is selected in the software by default, you need to deselect RTS/CTS; otherwise, you cannot enter commands.

Method used to retrieve the console account password for the USG6000 series
If you have a Telnet or web account with permissions higher than Level 3, you can change the password to the console port after logging in through Telnet or the web UI. Telnet login is used as an example: 1. Log in to the device using a Telnet account. 2. Change the password of the console user. For example, change the user name and password to admin and Password@123, respectively: system-view [sysname] user-interface console 0 [sysname-ui-console0] authentication-mode local user admin password cipher Password@123 [sysname-ui-console0] return

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top