Default login address and method used to restore the factory settings for the USG2000&5000 series

8

After the USG2000&5000 is shipped, you can log in to the web UI through GigabitEthernet0/0/0 by default.
The default login address is http://192.168.0.1. The device automatically uses the more secure protocol HTTPS to access the web UI.
On the web UI, choose System > Configuration File Management and click Restore Factory Default to restore factory settings.

Other related questions:
Default login address and method used to restore the factory settings for the USG6000 series
By default, the USG6000 series can be logged in through the management interface GigabitEthernet 0/0/0. The default login address is https://192.168.0.1:8443. On the web UI, choose System > Configuration File Management and click Restore Factory Default to restore the factory settings.

Method used to clear the configuration (restoring the factory settings) on the USG2000, USG5000, and USG6000.
The method used to clear the configuration *restoring the factory settings) on USG firewalls is as follows: 1. Hardware methods: Press and hold the RESET button on the device to boot based on the default configuration. Note: It is recommended that you press and hold the RESET button to restore to the default factory settings before the system is powered on. Note the following: You must press the RESET button for more than 10s. Release the RESET button before the system prompts to press Ctrl+B. You can restore the default configuration as follows: If the device is not powered on, press the RESET button and then power on the device. When six indicators on the panel blink at a frequency of about 2 Hz, release the RESET button. The device will boot using the default configuration. If the device is powered on, press and hold the RESET button and then release it in 10s. When you press Ctrl+B, six indicators on the panel blink at a frequency of about 2 Hz, indicating that the device successfully restores to the factory settings. Note: Before powering on the device, press and hold the RESET button. If the indicators blink immediately after you release the button, the button is successfully activated. You must release the RESET button in 10s after the device is powered on. Indicators blink only when the system prompts to press Ctrl+B instead of immediately blinking after the button is released. Do not press the RESET button for multiple times during the system boot. Otherwise, the system fails to restore the default configuration. After the system prompts to press Ctrl+B, if you press the RESET button during system boot or running, the system is not restarted and does not restore to default factory settings. It is recommended that you save the current configuration before pressing the RESET button. 2. Web UI: For the USG2000 and USG5000, on the web UI, choose System > Maintenance > Configuration Management, and click Restore Factory Configuration. For the USG6000, on the Web UI, choose System > Profile Management, and click Restore Factory Configuration. 3. CLI: reset saved-configuration (Clear the saved configuration.) 10:25:15 2015/03/13 The action will delete the saved configuration in the device. The configuration will be erased to reconfigure. Are you sure?[Y/N]y (The configuration will be cleared. Confirm? Press Y.) Now clearing the configuration in the device. 2015-03-13 10:25:19 FW %%01CFM/4/RST_CFG(l): When deciding whether to reset the saved configuration, the user presses Y. Info:Clear the configuration in the device successfully (Successfully cleared) reboot (Restart the device.) 10:25:31 2015/03/13 System will reboot, could you want to save current configuration [Y/N]?n (The system will restart. Save the current configuration? Press N. If you press Y, the original configuration is saved again and the configuration is not cleared.) System will reboot! Continue?[Y/N]:y (The device will restart. Press Y.) After the device is restarted, the configuration is cleared.

Method used to restore the factory settings of the USG2000 and USG5000 on the web UI
You can restore the factory settings on the web UI as follows: The restoration to the factory settings does not affect the saved profiles. 1. Choose System > Profile Management. The information in Current Configuration is the current configuration information. 2. Click Restore factory settings.

Method used to restore the factory settings of the USG6000 on the web UI
You can restore the factory settings on the web UI as follows: The restoration to the factory settings does not affect the saved profiles. 1. Choose System > Profile Management. The information in Current Configuration is the current configuration information. 2. Click Restore factory settings.

Configuring an address set for the USG2000&5000 series
The USG2000&5000 series supports configuring an address set using the web UI or CLI. An address set can contain IP addresses, network segments, IP address ranges, and MAC addresses and be contained in another address set. Configuring an address set using the web UI: Choose Firewall > Address > Address Set and then click Create in Address Set List. Enter or select the address set name and description, reference the address or address set, configure the IP address, and click Apply. Configuring an address set using the CLI: 1. Run the ip address-set address-set-name [ type { object | group } | vpn-instance vpn-instance-name ] * command in the system view to create an address set and access its view. 2. Run the address [ id ] { ip-address { 0 | wildcard | mask { mask-address | mask-len } } | range start-ip-address end-ip-address | address-set address-set-name | mac-address } [ description description ] command to add a member to this address set. You can run this command repeatedly to add multiple members to this address set. 3. Run the description text command to configure the address set description.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top