Displaying the bandwidth usage of an interface

23

You can run the display interface command to view the maximum bandwidth of an interface ( Max-bandwidth) and the rate of packets received or sent in the last 3000 seconds (Last 300 seconds input rate/Last 300 seconds output rate).

Other related questions:
The display interface brief and display interface commands display different interface bandwidth usage. Why
The display interface brief and display interface commands should display the same interface bandwidth usage. By default, the interval for traffic statistics on an interface is 300s. Within the first 300s, the statistics are instable. Wait for 300s and check the statistics, or run the set flow-stat interval command to change the interval for traffic statistics.

Backplane bandwidth of S series switches
The backplane bandwidth is the maximum traffic volume that can be exchanged between the interface processor or interface card and the data bus. The backplane bandwidth is also called switching bandwidth, which indicates the overall data switching capability of a switch, measured in Gbit/s. The higher backplane bandwidth indicates the greater data processing capability, but with higher design cost. For details about backplane bandwidth, contact your local Huawei office.

How can I display bandwidth restrictions on the SC?
To display bandwidth restriction information on the SC, perform the following operations: 1. Run the display command to go to the display view. 2. Run the bandwidth-restriction [id id] command to display details about all or specified bandwidth restrictions. For details, see HUAWEI SMC2.0 V500R002C00 SC Command Reference Guide.

Interfaces and bandwidths supported by the S1700
Interfaces and bandwidths supported by the S1700 are as follows: S1700-8-AC: 8 x 10/100BASE-T Ethernet interfaces S1700-8G-AC: 8 x 10/100/1000 BASE-T Ethernet interfaces S1700-16R: 16 x 10/100BASE-TX Ethernet electrical interfaces S1700-24R: 24 x 10/100BASE-TX Ethernet electrical interfaces S1700-26R-2T: 24 x 10/100BASE-TX Ethernet electrical interfaces and 2 x 10/100/1000BASE-T Ethernet electrical interfaces S1700-24-AC: 24 x 10/100BASE-T Ethernet interfaces S1700-52R-2T2P-AC: 48 x 10/100BASE-T Ethernet interfaces, 2 x 10/100/1000BASE-T Ethernet interfaces, and 2 x 1000BASE-X Ethernet optical interfaces S1724G: 24 x 10/100/1000BASE-T Ethernet interfaces S1728GWR-4P: 24 x 10/100/1000BASE-T Ethernet interfaces and 4 x 1000BASE-X Ethernet optical interfaces S1700-28FR-2T2P-AC: 24 x 10/100BASE-T Ethernet electrical interfaces, 2 x 10/100/1000BASE-T Ethernet electrical interfaces, and 2 x 1000BASE-X Ethernet optical interfaces S1700-28GFR-4P-AC: 24 x 10/100/1000BASE-T Ethernet electrical interfaces and 4 x 1000BASE-X Ethernet optical interfaces S1700-52FR-2T2P-AC: 48 x 10/100BASE-T Ethernet electrical interfaces, 2 x 10/100/1000BASE-T Ethernet electrical interfaces, and 2 x 1000BASE-X Ethernet optical interfaces S1700-52GFR-4P-AC: 48 x 10/100/1000BASE-T Ethernet electrical interfaces and 4 x 1000BASE-X Ethernet optical interfaces

Interface bandwidth OID information on S series switch
Interface bandwidth OID information on S series switches (except S1700): hwIfMonitorThresholdTable is used to query and configure alarm information and uses hwIfMonitorIndex as an index. The OID prefix of this table is 1.3.6.1.4.1.2011.5.25.41.1.7.1.1.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top