Whether the optical transceiver of the USG2000&5000 supports the DDM function

30

Currently, Huawei SFP+ and ESFP support digital diagnostic monitoring (DDM), and Huawei SFP does not support DDM.
For example: ESFP:
-------------------------------------------------------------
Common information:
Transceiver Type :1000_BASE_LX_SFP
Connector Type :LC
Wavelength(nm) :1310
Transfer Distance(m) :10000(90um)
Digital Diagnostic Monitoring :YES
Vendor Name

Other related questions:
Whether the optical transceiver of the USG6000 supports the DDM function
Currently, Huawei SFP+ and ESFP support digital diagnostic monitoring (DDM), and Huawei SFP does not support DDM. For example: ESFP: ------------------------------------------------------------- Common information: Transceiver Type :1000_BASE_LX_SFP Connector Type :LC Wavelength(nm) :1310 Transfer Distance(m) :10000(90um) Digital Diagnostic Monitoring :YES Vendor Name

Whether the USG2000&5000 support the Telnet function
By default, the USG2000&5000 have the Telnet function enabled, and users can directly use the initial administrator account admin to log in to the device.

Optical transceiver optical fiber types applicable to optical interfaces of the USG2000&5000
Huawei optical interface modules are recommended. The optical interface modules of other vendors may cause device faults due to incompatibility. You need to select the local optical interface module according to the type of the peer optical interface module, considering the rate and single-mode or multi-mode. If the types of optical interface modules at two ends are inconsistent, communications may fail. Optical transceiver optical fiber types applicable to optical interfaces of the USG2000&5000 1. 1000M Ethernet optical interface attribute The 100M Ethernet optical interface resides on the 2FE+2FE Combo interface card. Description of the 100M Ethernet optical interface attribute Interface standard 100Base-TX Connector type SFP Working mode Full duplex Rate 100 Mbit/s 100M optical transceiver attribute table Model eSFP-FE-LX-SM1310 Optical fiber type Single-mode Model S-SFP-FE-LH40-SM1310 Optical fiber type Single-mode Model S-SFP-FE-LH80-SM1550 Optical fiber type Single-mode 2. 1000M Ethernet optical interface attribute The 1000M Ethernet optical interface resides on the 18FE+2SFP interface card. Description of the 1000M Ethernet optical interface attribute Interface standard 1000Base-LX/1000Base-SX/1000Base-T Connector type SFP Working mode Full duplex Rate 1000 Mbit/s 1000M optical transceiver attribute table Model eSFP-GE-SX-MM850 Optical fiber type Multi-mode Model SFP-GE-LX-SM1310 Optical fiber type Single-mode Model S-SFP-GE-LH40-SM1310 Optical fiber type Single-mode 3. 100/1000M Ethernet optical interface attribute The 100/1000M Ethernet optical interface resides on the main board and 16GE+4SFP interface card. Description of the 100/1000M Ethernet optical interface attribute Interface standard 1000Base-LX/1000Base-SX/1000Base-T Connector type SFP Working mode Full duplex Rate 100/1000 Mbit/s The 100/1000M Ethernet optical interface applies to the 100/1000M optical transceiver. 4. 10GE optical interface attribute Connector type SFP+ Interface cable Optical fiber Working mode Full duplex Rate 10 Gbit/s Interface standard IEEE 802.2/802.3 Supported frame format Ethernet_II Supported network protocol TCP/IP 10GE optical transceiver attribute table Model OMXD30000 Optical fiber type Multi-mode Model OSX010000 Optical fiber type Single-mode Model OSX040N01 Optical fiber type Single-mode

Whether the USG2000&5000 support capturing packets
You can enable the packet capture function on the USG2000&5000 as follows: 1. Configure the packet capture queue. [USG] packet-capture all-packet queue 0 interface GigabitEthernet 0/0/1 2. Enable the packet capture function. [USG] packet-capture startup manual 3. Save packets in the specified queue as file 1.cap on the device. The default directory is hda1:/. [USG] packet-capture queue 0 to-file 1.cap 4. Use FTP to download file 1.cap from the device, use the packet capture software to open the file, and analyze the captured packets. 5. Clear the packet capture queue and release the memory. After confirming that the host has completed receiving the packets, delete all packets from the queue. reset packet-capture queue 0

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top