Can I add inconsecutive numbers in batches on the U1960?

Run the vlan batch command in the system view to create VLANs in a batch. Create 10 contiguous VLANs: VLAN 11 to VLAN 20. system-view [HUAWEI] vlan batch 11 to 20 Create 10 discontiguous VLANs in a batch: VLAN 10, VLAN 15 to VLAN 19, VLAN 25, VLAN 28 to VLAN 30. system-view [HUAWEI] vlan batch 10 15 to 19 25 28 to 30 NOTE: You can create a maximum of 10 discontiguous VLANs or VLAN range at one time. If there are more than 10 VLANs, run this command multiple times. For example, the vlan batch 10 15 to 19 25 28 to 30 command creates four discontiguous VLAN ranges.

You can add interfaces to a VLAN in a batch using a port group, and directly add access interfaces to a VLAN in a batch in the system view. Access interface # Add GE0/0/1-GE0/0/5 to VLAN 10 in a batch. Add interfaces to a VLAN in a batch using a port group. system-view [HUAWEI] port-group pg1 [HUAWEI-port-group-pg1] group-member gigabitethernet0/0/1 to gigabitethernet0/0/5 [HUAWEI-port-group-pg1] port link-type access [HUAWEI-port-group-pg1] port default vlan 10 Add interfaces to a VLAN in a batch in the VLAN view. system-view [HUAWEI] vlan 10 [HUAWEI-vlan10] port gigabitethernet 0/0/1 to 0/0/5 NOTE: Before performing this operation, configure interfaces to be added to a VLAN as access interface. Trunk interface # Add GE0/0/1-GE0/0/5 to VLAN 10 and VLAN 20 in a batch. system-view [HUAWEI] port-group pg1 [HUAWEI-port-group-pg1] group-member gigabitethernet0/0/1 to gigabitethernet0/0/5 [HUAWEI-port-group-pg1] port link-type trunk [HUAWEI-port-group-pg1] port trunk allow-pass vlan 10 20Hybrid interface # Add GE0/0/1-GE0/0/5 to VLAN 10 and VLAN 20 in a batch. system-view [HUAWEI] port-group pg1 [HUAWEI-port-group-pg1] group-member gigabitethernet0/0/1 to gigabitethernet0/0/5 [HUAWEI-port-group-pg1] port link-type hybrid [HUAWEI-port-group-pg1] port hybrid tagged vlan 10 [HUAWEI-port-group-pg1] port hybrid untagged vlan 20

You can import static binding entries to an S series switch (except the S1700) in batches using either of the following methods: Method 1: 1. Create a .txt file and paste copied binding entries to the .txt file. 2. Modify the binding entries (such as IP addresses or MAC addresses) as needed. 3. Log in to the switch, enter the system view, and copy and paste the modified binding entries. Method 2: 1. Configure a binding entry on the switch and save the configuration. 2. Export the configuration file through FTP or TFTP. 3. Open the configuration file, locate the pre-configured user-bind static command, and configure more binding entries in the same format in the command. 4. Save the file. 5. Import the modified configuration file to the switch through FTP or TFTP. If the file name is changed, specify the new configuration file for next startup.

You cannot add soft clients in batches on the SMC2.0.

Run the config modify subscriber dn 8121 operate add outgoingrights ddd number 10 command to add the international toll call right for numbers 8121 to 8230. Run the config modify subscriber dn 8121 operate del outgoingrights ddd number 10 command to delete the international toll call right for numbers 8121 to 8230.