Which command can be run to modify the dial-up idle period

0

You can run the dialer timer idle seconds command to set the allowed idle period for the link after a call is established on the interface, that is, time period during which no Interesting packet is not transmitted.

In the command, seconds indicates the allowed idle period of the link, which is an integer ranged from 0 to 65535 and is measured by seconds. The default value of the period is 120 seconds.

Other related questions:
Which command can be run to set the DCC automatic dial-up interval
You can run the dialer timer autodial seconds command to set the interval of DCC automatic dial-up. In the command, seconds indicates the interval between the latest call to the next call attempt, which is an integer ranged from 1 to 604,800 and is measured by seconds. The interval of DCC automatic dial-up is 300 seconds by default. Note: Before run the command, run the dialer enable-circular command to enable the circular DCC.

Which command is used to set the auto-dial interval

The dialer timer autodial seconds command is used to set the auto-dial interval.

seconds specifies the auto-dial interval. The value is an integer that ranges from 1 to 604800, in seconds. By default, the auto-dial interval is 300 seconds.
NOTE:
Before using the dialer timer autodial seconds command, ensure that the C-DCC function has been enabled by the dialer enable-circular command.

Which command is used to change the maximum link idle time

The dialer timer idle seconds command is used to set the maximum link idle time on an interface. During this period of time, no Interesting packet is transmitted over the link.

seconds specifies the maximum link idle time. The value is an integer that ranges from 0 to 65535, in seconds. The default value is 120.


How to view the versions and hardware types of S series switches
On S series switches (except the S1700): - Run the display version command to view version information, including the model and running time. Using the S5720HI as an example, the following information is displayed: [HUAWEI] display version Huawei Versatile Routing Platform Software VRP (R) software, Version 5.160 (S5720 V200R007C00) //VRP version and release version Copyright (C) 2000-2014 HUAWEI TECH CO., LTD HUAWEI S5720-56C-HI-AC Routing Switch uptime is 0 week, 1 day, 3 hours, 24 minutes ///Hardware name and running time ES5D2T52C001 0(Master) : uptime is 0 week, 1 day, 3 hours, 23 minutes 4095M bytes DDR Memory 64M bytes FLASH Pcb Version : VER.A Basic BootROM Version : 0207.0015 Compiled at Mar 20 2014 , 22:53:47 BootLoad Version : 0207.0015 Compiled at Mar 14 2014 , 13:33:43 CPLD Version : 256 Software Version : VRP (R) Software, Version 5.160 (V200R007C00) //VRP version and software version SLOT2 information //Information about rear cards. If no rear card is available, this field is not displayed Pcb Version : ES5D21X04S01 VER.A PWR1 information //Information about pluggable power modules. If no pluggable power module is available, this field is not displayed. Pcb Version : PWR VER.A - Run the display device command to view the type and status of components on the switch. The Register field indicates whether a component is registered. [HUAWEI] display device S7712's Device status: Slot Sub Type Online Power Register Status Role 3 - - Present PowerOff Unregistered - NA 4 - ES0D0G48TA00 Present PowerOn Registered Normal NA 13 - - Present PowerOn Unregistered - Slave 14 - ES0D00SRUA00 Present PowerOn Registered Normal Master PWR1 - - Present PowerOn Registered Normal NA CMU1 - LE0DCMUA0000 Present PowerOn Registered Normal Master FAN1 - - Present PowerOn Registered Normal NA

Can an outbound interface be specified for dial-up in the resource-shared DCC dial-up method
Yes. You can run the dialer route ip next-hop-address user hostname | broadcast * dial-string autodial | interface interface-type interface-number * command to specify an outbound interface for dial-up.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top