How to bulk delete the outgoing call rights for numbers on the U1900 series unified gateway

For details, see section 6b "Configuring Prefixes" in the eSpace UC V200R003 IPT Quick Configuration Guide .

System software parameter 270 is used to control whether to play the call forwarding announcement on the U1900 series unified gateway. To disable the call forwarding announcement, perform the following steps: 1. Check the value of software parameter 270. (Value 0 indicates that the call forwarding announcement is disabled, and value 1 indicates that the call forwarding announcement is enabled.) If Current Value is empty, the default value 1 is used. [%eSpace U1981(config)]#show softargu configinfor id 270 ID : 270 Type : service Current Value: -- Desc : Whether to hear the prompt tone about the transfer reason [range: 0(NO), 1(YES)][default:1] 2. Change the value of software parameter 270 as required. config softargu type 270 value 0 //Call forwarding announcement is disabled. the value is-0 , when perform the forward service will be not any prompt config softargu type 270 value 1 //Call forwarding announcement is enabled. the value is 1 , when perform the forward service will be get tone to prompt- the call is redirecting- 3. Save the modification.

A prefix is a string consisting of first several digits or all digits of a called number. Determine prefixes based on the dialing habits and the user number plan. Procedure: Note: Before adding the local call prefix, you must add the national toll call prefix and international toll call prefix; otherwise, the local call prefix cannot be added. 1. Configuring an outgoing prefix on the CLI Add outgoing prefix 0. Set the call category to basic (basic service call), set the call attribute to local (local call), enable called number change, set the number change index to 1, and set the office route selection code to 0. config add prefix dn 0 callcategory basic callattribute local cldpredeal yes cldindex 1 officeselectcode 0 Parameter description: callcategory: indicates the call type. basic: indicates basic services such as intra-office and local call services. callattribute: indicates the call attribute. For basic services, the call attribute can be inter (intra-office calls), local (local calls), interlocal (intra-office or local calls), ddd (national toll calls), idd (international calls), and emergency (emergency calls). cldpredeal: indicates whether to change a called number. If the value of this parameter is yes, you must set cldindex. cldindex: indicates the called number change index, which is defined using the config add predeal command. clipredeal: indicates whether to change a calling number. If the value of this parameter is yes, you must set cliindex. cliindex: indicates the calling number change index, which is defined using the config add predeal command. 2. Configuring an outgoing prefix on the web page (for U1900 V100R001C20 and V200R003) (1) Log in to the web management system of the U1900. (2) Choose Trunk > Prefix Configuration. On the prefix configuration page, click Create. C. In the dialog box for creating a prefix, configure the prefix. (4) Click Data Save in the upper right corner of the web page. For detailed parameter descriptions, see the online help of the web management system.

The following uses the U1930 as an example. Commands for modify the outgoing call rights for a single user: [%eSpace U1930(config)]#config modify subscriber dn 6101 priorlevel default operateout del outgoingrights local //Delete the outgoing local call right for user number 6101. [%eSpace U1930(config)]#config modify subscriber dn 6101 priorlevel default operateout del outgoingrights local&ddd //Delete the outgoing local and national toll call rights for user number 6101. [%eSpace U1930(config)]#config modify subscriber dn 6101 priorlevel default operateout add outgoingrights local //Add the outgoing local call right for user number 6101. [%eSpace U1930(config)]#config modify subscriber dn 6101 priorlevel default operateout add outgoingrights local&ddd //Add outgoing local and national toll call rights for user number 6101. [%eSpace U1930(config)]# config modify subscriber dn 6101 priorlevel default operateout add outgoingrights Inter&local&ddd //Modify the outgoing call rights for user number 6101 to outgoing intra-office, local, and national toll call rights. Commands for modify the outgoing call rights for multiple users in batches: [%eSpace U1930(config)]#config modify subscriber dn 6101 priorlevel default operateout del outgoingrights local number 100 //Delete the outgoing local call right for 100 user numbers starting from 6101. [%eSpace U1930(config)]#config modify subscriber dn 6101 priorlevel default operateout add outgoingrights local number 100 //Add the outgoing local call right for 100 user numbers starting from 6101. %eSpace U1930(config)]# config modify subscriber dn 6101 priorlevel default operateout add outgoingrights Inter&local&ddd number 100 //Modify the outgoing call rights for user numbers starting from 6101 to outgoing intra-office, local, and national toll call rights. Note: inter indicates the intra-office call right, local indicates the local call right, ddd indicates the national toll call right, and idd indicates the international toll call right.

For detailed configuration of password-based outgoing call rights for users on the U1900, see Configuration > Feature Guide > Voice Service > Password-based Call Barring in the product documentation To WeiKnow To Live Chat