What's the function of pbx number-parameter?

9

If the trunk function is not used, change the dialup timer value of the AT0 trunk to 0. The AR does not need to spend 5s on detecting the ringback tone. A user needs to wait for only 3s to hear the ringback tone.
Run the pbx number-parameter 40 0 command to set parameter 40 to 0.
The modification may cause failures of calls transferred through trunks. The pbx number-parameter 40 0 command can be used only when POTS or SIP phones make outgoing calls through AT0 trunks.

Other related questions:
Does the U1980 V200R003 version support the sub-PBX function?
The U1900 voice gateways of V100R001C20 and V200R003 do not support the sub-PBX function.

What are SIP AGs and PBXs, and what are the differences between them
Access devices on the IP Multimedia Subsystem (IMS) provide various access modes and convert various services into a uniform format that can be transmitted. On the IMS, an access device is called access gateway (AG). AGs play an important role on the IMS and are connected to users. AGs and media gateway controllers (MGCs) use Session Initiation Protocol (SIP). SIP-based AGs are called SIP AGs. A traditional private branch exchange (PBX) manages the incoming and outgoing calls of an enterprise. It connects the enterprise to the Public Switched Telephone Network (PSTN) and provides services for devices such as telephones, fax machines, and modems. It allows users in the enterprise to call each other using extension phones and routes inter-office calls to the PSTN through a trunk line. Traditional PBXs cannot meet the requirements of computer telephony integration (CTI) and voice over IP (VoIP). In addition, these PBXs are expensive and do not use standard and open platforms, creating difficulties in interconnecting PBXs of different vendors. IP PBXs overcome the limitations of traditional PBXs. IP PBXs are based on the IP protocol and provide both local exchange and IP user access functionality. IP PBXs integrate the voice communications system of an enterprise into the enterprise's data network so that the enterprise can build a uniform voice and data network connecting branches, offices, and staff around the world. The AR1200/2200/3200 can function as a PBX to provide traditional PBX functions and IP PBX functions. SIP AGs and PBXs have the following differences: -PBXs have two functions. PBXs can serve as switching devices on a private network to locate voice users' addresses and process other services. PBXs also allow users on the private network to access the IMS or PSTN through SIP trunks. -SIP AGs provide only the second function of PBXs. SIP AGs can be considered to be a plain old telephone service (POTS) that can register with the IMS using SIP trunks. PBXs use SIP trunks to register with other SIP servers. SIP AGs register with the IMS using POTS user numbers. PBXs and SIP AGs provides the same services. However, PBXs provide the services by themselves.

Can the AR connect to the PBX
A PBX often provides E1 (DB9) and FXO (RJ11) interfaces. E1 and FXO interfaces can connect to the AR.

How to add a sub-PBX on the SoftCo
1. Configure a sub-PBX. By default, all resources have been allocated to the sub-PBX numbered 0. Before adding a new sub-PBX, run the config modify subpbx command to reallocate resources on the sub-PBX numbered 0. Otherwise, adding a sub-PBX using the command will fail. Change the maximum number of conference participants for the sub-PBX numbered 0 (sub-PBX 1 in this example) to 15. The maximum number of participants must be set based on the site requirements. config modify subpbx no 0 maxconfseat 15 Add a sub-PBX and allocate participant resources to it. The total number of sub-PBXs cannot exceed the threshold allowed by the license. 2. Query the detailed information about the sub-PBX: show subpbx

What gateway models can work as active and standby PBXs
The U1911, U1960, U1980, and U1981 all support the active/standby mode.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top