How can I query the MAC address of the VCN500?

Ping the IP address of the NE on a computer, and run the ARP -A command to query the MAC address mapping table.

To query the network port MAC address, log in to the BMC CLI and run the ipmcget -d macaddr command.

Method used to check the IP address and MAC address of a storage device: 1. Use the SSH tool to log in to the debug mode. 2. Run ip a to check the IP address and MAC address of the storage device. Storage:~ # ip a a: lo: mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/16 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever b: sit0: mtu 1480 qdisc noop link/sit 0.0.0.0 brd 0.0.0.0 c: eth0: mtu 1500 qdisc pfifo_fast master bond0 qlen 1000 link/ether 78:1d:ba:cc:c7:6b brd ff:ff:ff:ff:ff:ff d: eth1: mtu 1500 qdisc pfifo_fast master bond0 qlen 1000 link/ether 78:1d:ba:cc:c7:6b brd ff:ff:ff:ff:ff:ff e: eth2: mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 78:1d:ba:cc:c7:69 brd ff:ff:ff:ff:ff:ff inet 129.22.242.4/16 brd 129.22.255.255 scope global eth2 inet 172.168.128.102/16 brd 172.168.255.255 scope global eth2:1 inet6 2002:8116:93d:b:7a1d:baff:fecc:c769/64 scope global dynamic valid_lft 2591901sec preferred_lft 604701sec inet6 fec0::b:7a1d:baff:fecc:c769/64 scope site dynamic valid_lft 2591901sec preferred_lft 604701sec inet6 fec0::11/10 scope site tentative flags 08 valid_lft forever preferred_lft forever inet6 fe80::7a1d:baff:fecc:c769/64 scope link valid_lft forever preferred_lft forever f: eth3:mtu 1500 qdisc noop qlen 1000 link/ether 78:1d:ba:cc:c7:68 brd ff:ff:ff:ff:ff:ff g: bond0: mtu 1500 qdisc noqueue link/ether 78:1d:ba:cc:c7:6b brd ff:ff:ff:ff:ff:ff inet 127.127.127.11/24 brd 127.127.127.255 scope global bond0 inet6 fe80::7a1d:baff:fecc:c76b/64 scope link valid_lft forever preferred_lft forever h: bond1: mtu 1500 qdisc noop link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff i: bond2: mtu 1500 qdisc noop link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff Note: Use bond0 as an example. 78:1d:ba:cc:c7:6b following link/either is the MAC address and 127.127.127.11 following inet is the IP address.

To query the MAC address of a standalone SC, log in to the standalone SC and run the ifconfig -a command.

Querying the MAC address of an eSpace 7900 IP phone On the LCD screen, choose Application > Status > Network status. The value of Ethernet MAC displayed at the bottom of the Network status screen is the MAC address of the 7900 IP phone. Querying the MAC address of an eSpace 8950 IP phone 1. On the LCD screen, tap four block icons. On the Application tab page, tap Setting. 2. On the displayed screen, tap About IP Phone and then Status On the displayed screen, you can view the peripheral status, network status, and MAC address of the phone.