NAS

4

The network-attached storage (NAS) unifies distributed and independent data into a large-scale and centralized data center to provide file sharing services to different hosts and application servers.

Other related questions:
How Can I View the Version of a Clustered NAS Engine?
Two methods are available. The first method: on the command-line interface (CLI) 1.Log in to the CLI using a master account. 2.Run the upgrade show command to view the current version of the system. N8000>upgrade show N8000V200R001C00SPC007The second method: on the ISM 1.In the navigation tree on the ISM, choose All Devices > Clustered NAS Storage System. 2.In the Basic System Information area of the function pane, view Engine Version.

Which V3 versions can use NAS?
V300R001 supports only SAN. Both SAN and NAS are supported by V300R002 and later versions. The following model is special. 1) NAS is not supported by OceanStor 2800 V3; 2) NAS is not supported by OceanStor 2600 V3 Video Surveillance Edition; 3) NAS is only supported by OceanStor 2200 V3 with conditions: V3 version >= V300R006 and Memory Cache >= 16GB.

How to configure a route for the N8500 NAS engine?
1.In the navigation tree of the ISM main interface, choose Clustered NAS Storage System > Device Info. 2.Expand Device Info and select a clustered NAS engine to be configured. 3.In the function pane, choose Network > Route Management. The Route Management dialog box is displayed. 4.In the Route Table list box, view the information about the existing routes. 5.Click Add. The Add Route dialog box is displayed. 6.In the Node drop-down list, select a clustered NAS engine node to be configured. 7.In the IP Address text box, enter the IP address of the route to be added. 8.In the Subnet Mask text box, enter the subnet mask of the route to be added. 9.In the GateWay text box, enter the gateway IP address of the N8500. 10.Click OK. The Result dialog box is displayed. 11.Click Close.

Configuration of the NAS-Initialized VPN on the USG2000 and USG5000
The method used to configure the NAS-Initialized VPN (local authentication) on the USG2000 and USG5000 is as follows: The PC is connected to the LAC by means of PPP dialup. The LAC and LNS communicate over a tunnel on a WAN. The user accesses the network using the domain name. The user name and password are authenticated on the LAC and LNS in local authentication mode. 1. Configure the LAC. a. Create the virtual interface template and bind it with the interface. system-view [LAC] interface Virtual-Template 1 [LAC-Virtual-Template1] ppp authentication-mode chap [LAC-Virtual-Template1] quit [LAC] interface GigabitEthernet 0/0/1 [LAC-GigabitEthernet0/0/1] pppoe-server bind virtual-template 1 [LAC-GigabitEthernet0/0/1] quit b. Enable the L2TP. [LAC] l2tp enable c. Create and configure the L2TP group. [LAC] l2tp-group 1 [LAC-l2tp1] tunnel name LAC [LAC-l2tp1] start l2tp ip 202.38.163.1 domain domain1.com [LAC-l2tp1] tunnel authentication [LAC-l2tp1] tunnel password cipher Password1 [LAC-l2tp1] quit d. Configure the domain name suffix separator. [LAC] l2tp domain suffix-separator @ e. Set the user name and password (consistent with those configured on the user side). [LAC] aaa [LAC-aaa] local-user vpdnuser@domain1.com password cipher Hello123 f. Configure the domain accessed by the user. [LAC-aaa] domain domain1.com 2. Configure the LNS. a. Create virtual template Virtual-Template and configure the related information. [LNS] interface virtual-template 1 [LNS-Virtual-Template1] ip address 192.168.0.1 255.255.255.0 [LNS-Virtual-Template1] ppp authentication-mode chap [LNS-Virtual-Template1] quit b. Enable the L2TP. [LNS] l2tp enable c. Create and configure the L2TP group. [LNS] l2tp-group 1 [LNS-l2tp1] tunnel name LNS [LNS-l2tp1] allow l2tp virtual-template 1 remote LAC [LNS-l2tp1] tunnel authentication [LNS-l2tp1] tunnel password cipher Password1 e. Configure forcible CHAP verification on the local end. [LNS-l2tp1] mandatory-chap [LNS-l2tp1] quit f. Configure the domain name suffix separator. [LNS] l2tp domain suffix-separator @ g. Set the user name and password (consistent with those configured on the LAC). [LNS] aaa [LNS-aaa] local-user vpdnuser@domain1.com password cipher Hello123 h. Configure the domain name accessed by the user. [LNS-aaa] domain domain1.com i. Configure the address pool allocated to the user. [LNS-aaa-domain-domain1.com] ip pool 1 192.168.0.2 192.168.0.100 [LNS-aaa-domain-domain1.com] quit [LNS-aaa] quit Note: Because the addresses in the IP address pool are not in the same network segment as the intranet addresses, you need to configure the route to network segment 192.168.0.0 on the HQ device, and set the next hop address to 192.168.1.1. j. Allocate an address in the IP address pool to the peer interface. [LNS] interface virtual-template 1 [LNS-Virtual-Template1] remote address pool 1 [LNS-Virtual-Template1] quit

How to view the hardware information of the N8000 clustered NAS engine?
1.In the navigation tree of the ISM main interface, choose Clustered NAS Storage System > Device Info. 2.In the function pane, you can view the specific hardware status and information though clicking this hardware module.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top