Method used to change the number of concurrent disks in Solaris 10

1

1. Modify the configuration file. Run vi to open the /etc/system file and modify or add the parameter of concurrent disks. In this example, change the number of concurrent disks to 5, save the setting, and exit.
set sd:sd_max_throttle =5
set ssd:ssd_max_throttle =5
2. Run reboot to restart the host to make the configuration take effect.

Other related questions:
Method used to change the number of concurrent disks on VMware ESX
Method used to change the number of concurrent disks on VMware ESX 4.0: 1. Log in to the server by using the VMware vSphere Client. 2. Select the server to be configured and choose Configuration > Advanced Configuration to open the Advanced Configuration page. 3. On the Advanced Configuration page, change the number of concurrent disks. Specifically, on the Advanced Configuration page, select Disk on the navigation bar on the left, select Disk.SchedNumReqOutstanding on the left, and specify the desired value in the box. Click OK to exit.

Method used to configure the iSCSI initiator in Solaris 10
Method used to configure the iSCSI initiator in Solaris 10: 1. Check whether iSCSI services have been started. Run svcs -a |grep iscsi to check the status of iSCSI. If the status of iSCSI is online, iSCSI services have been started. Otherwise, run svcadm enable iscsi_initiator to start iSCSI services. 2. Configure the Solaris iSCSI initiator. Run iscsiadm add discovery-address [ip addr:portal no] # iscsiadm add discovery-address xxx.xxx.xxx.xxx:3260 to configure the Solaris iSCSI initiator. 3. Add an initiator corresponding to the host on the array side and map it to the LUN. 4. (Optional) Methods used to search for the iSCSI target: a. If a dynamic discovery device (SendTargets) has been configured, run the following command: # iscsiadm modify discovery --sendtargets enable b. If a dynamic discovery device (iSNS) has been configured, run the following command: # iscsiadm modify discovery --isns enable c. If a static discovery device has been configured, run the following command: # iscsiadm modify discovery --static enable 5. Run devfsadm -i iscsi to create links for iSCSI devices. 6. Run format to check iSCSI disks.

Method used to change concurrent disks in the AIX operating system
To change concurrent disks, you need to stop service operations and perform the following steps: 1. Run lspv to check the volume group and disk status. 2. After services are stopped, run varyoffvg [vg_name] to activate specified volume groups. 3. Run lsattr -El updiskX | grep queue_depth to check the queue depth of specified disks. 4. Run chdev -a queue_depth=32 -l updiskX to change the queue depth of specified disks.

Method used to modify the number of concurrent disks by using Fibre Channel HBA in Linux
You can perform the following operations to modify the number of concurrent disks by using Fibre Channel HBA in Linux: The procedures are as follows (QLogic HBA is used as an example): 1. Query whether the host is installed with Fibre Channel HBA and query the HBA manufacturer. Run the lspci |grep "Fibre Channel" command to query HBA information. 2. Modify the configuration file. Run vi to open the /etc/modprobe.conf file and modify or add the parameter of concurrent HBA. Note: Modify the /etc/modprobe.conf.local file in SUSE and do not modify the /etc/modprobe.conf file. 3. Run the multipathing command upUpdate. If the actual operating system and hardware are different, the information to be displayed may also be different. 4. Run the reboot command to restart the host. 5. Run the lsscsi -l command to check whether the parameter of concurrent HBA takes effect.

Method used to change the ID of an OceanStor V3 disk enclosure
The ID of an OceanStor V3 disk enclosure cannot be changed.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top