Types of and installation requirements on the guide rail matching the Ethernet switch

5

Types of and installation requirements on the guide rail matching the Ethernet switch:
The installation accessories of a 1 U Ethernet switch contain guide rails with bottom support. The depth of guide rails can be adjusted and guide rails can be installed on SC611-20 cabinets.

If you need to install adjustable guide rails on other cabinets, the following requirements on the cabinet must be met:
1. The cabinet complies with the requirements of the IEC 60297 standard, in which the dimension of mechanical structures is 482.6 mm. The angle opening width of cabinets is 450 mm.
2. The distance between mounting bars at the front and rear of the cabinet ranges from 600 mm to 900 mm.
3. Holes on the installation angle gauge (mounting bar) are either of the following:
1) Square holes (size �?9 mm × 9 mm)
2) Round holes (diameter �?7 mm)
4. Minimum transverse space inside the cabinet: �?475 mm.

Other related questions:
What types of guide rails should I use for Ethernet switches and what are the installation requirements?
Bottom support-type guide rails and adjustable guide rails are delivered with a 1 U Ethernet switch. Such guide rails can be installed in the SC611-20 cabinet. If you need to install adjustable guide rails in another model of cabinet, the following must be met: ? The cabinet size is consistent with that of the 19-inch (482.6 mm) IEC 60297 series. ? The distance between front and rear channels ranges from 600 mm to 900 mm. ? Holes on the channels can be either of the following: ? Square holes (side length �?9 mm) ? Round holes (diameter �?Ф 7 mm) ? The minimum horizontal distance in the cabinet cannot be less than 475 mm.

Guide rails matching S2200T/S2600T/S5500T/S5600T/S5800T/S6800T controller enclosures and requirements of installing guide rails
Guide rails matching S2200T/S2600T/S5500T/S5600T/S5800T/S6800T engines, controller enclosures, and disk enclosures and requirements of installing guide rails: The installation accessories of a 4 U file engine contain guide rails with side support. The depth of guide rails can be adjusted and guide rails can be installed on SC611-20 cabinets. If you need to install adjustable guide rails on other cabinets, the following requirements on the cabinet must be met: 1. The cabinet complies with the requirements of the IEC 60297 standard, in which the dimension of mechanical structures is 482.6 mm. The angle opening width of cabinets is 450 mm. 2. The distance between mounting bars at the front and rear of the cabinet ranges from 690 mm to 770 mm. 3. Holes on the installation angle gauge (mounting bar) are either of the following: 1) Square holes (size �?9 mm × 9 mm) 2) Round holes (diameter �?7 mm) 4. Minimum transverse space inside the cabinet: �?475 mm.

What types of guide rails should I use for file engine nodes and what are the installation requirements?
Side support-type guide rails and adjustable guide rails are delivered with a 4 U file engine node. Such guide rails can be installed in the SC611-20 cabinet. If you need to install adjustable guide rails in another model of cabinet, the following must be met: ? The cabinet size is consistent with that of the 19-inch (482.6 mm) IEC 60297 series. ? The distance between front and rear channels ranges from 690 mm to 770 mm. ? Holes on the channels can be either of the following: ? Square holes (side length �?9 mm) ? Round holes (diameter �?Ф 7 mm) ? The minimum horizontal distance in the cabinet cannot be less than 475 mm.

What types of guide rails should I use for controller enclosures or disk enclosures and what are the installation requirements?
Bottom support-type guide rails and adjustable guide rails are delivered with 2 U and 4 U controller enclosures or disk enclosures. Such guide rails can be installed in the SC611-20 cabinet. If you need to install adjustable guide rails in another model of cabinet, the following must be met: ? The cabinet size is consistent with that of the 19-inch (482.6 mm) IEC 60297 series. The open size is 450 mm. ? The distance between front and rear channels ranges from 600 mm to 900 mm. ? Holes on the channels can be either of the following: ? Square holes (side length �?9 mm) ? Round holes (diameter �?Ф 7 mm) ? The minimum horizontal distance in the cabinet cannot be less than 475 mm.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top