How to query routing information through the web NMS on an AR router

21

To query routing information, do as follows:
1. Choose IP Service > Route > Routing Table on the web page.
2. You can query all routing tables, or select a routing type or destination IP address/subnet mask to query specified routes, depending on actual needs.

Other related questions:
How to configure a route through the web NMS on an AR router
To configure a static route, do as follows: 1. Choose IP Service > Route > Static Route Configuration. . 2. Click Create in the IPv4 Static Route Configuration Table or IPv6 Static Route Configuration Table according to requirements to enter the parameter configuration page. 3. Configure parameters one by one, and click OK to complete the configuration. To configure a dynamic route, do as follows: - Configure the OSPF function. 1. Choose IP Service > Route > Dynamic Route Configuration > OSPF to enter the OSPF List page. 2. Click Create, enter parameters, and click ok to create an OSPF process. 3. On the OSPF List page, select the new OSPF process, click Advanced at the right side, click the Basic or Advanced tab page, and modify the OSPF process parameters according to requirements. - Configure the BGP function. 1. Choose IP Service > Route > Dynamic Route Configuration > BGP, configure parameters, and click Apply. 2. On the Peer Configuration List page, click Create, enter parameters, and click ok to create a BGP neighbor.

Query interface traffic through the web NMS on an AR router
1. Choose IP Service > IP Accounting > Traffic Statistics. 2. Click Refresh. If the operation is successful, the traffic statistics about the current IP address of the device is displayed in the Traffic Statistics Ranking list. 3. Click Total Traffic (Packets) in the list head to arrange the traffic by size in ascending or descending manner.

How to enable the web function on an AR router
The methods of enabling the web function on an AR router are as follows: Method 1: Default web login 1. Connect a PC to the router over the management interface through a network cable. 2. Configure an IP address for the PC. Configurable network segment: 192.168.1.2~192.168.1.254. 3. Open a browser, enter the URL "https://192.168.1.1" in the address bar, and click Enter to enter the user login page. 4. Enter login information. 5. Configure the router through the web NMS page. Note: If you cannot enter the web NMS page, the software version you use does not support the default web login method. Please try the following method: Method 2: Non-default web login 1. Connect a PC to the router over the CON/AUX interface through a console configuration cable. 2. Enable the terminal emulation software on the PC, create a connection, and set an interface for the connection and other communication parameters. 3. Press Enter until the following information is displayed to remind users of configuring a verification code. 4. Connect a PC to the router over the management interface through a network cable. 5. Configure an IP address for the router for management. 6. Enable the web service. 7. Configure an HTTPS user and a user level. 8. Configure an IP address for the PC. 9. Open a browser, enter the URL "https://192.168.1.1" in the address bar, and click Enter to enter the user login page. 10. Configure the router through the web NMS page.

Method of creating a VLAN through the web NMS on an AR router
The web NMS of the AR series routers does not support VLAN creation or adding of interfaces to a created VLAN. You can create a VLANIF interface, and add the interface to the VLAN. 1. Choose LAN Access > LAN >VLAN Interface to enter the VLAN interface configuration page. 2. In the VLAN Interface List area, click Create. 3. On the Create VLAN Inter page, select parameters or enter values according to requirements to configure a VLAN interface. On the NMS page, only interfaces of the access and trunk types can be configured. Hybrid type interfaces cannot be configured. Use command lines to create a VLAN. In the system view, run the vlan command or the vlan batch command.

How to upgrade the system software through the web NMS on an AR router
To upgrade the system software through the web NMS on an AR router, do as follows: 1. Choose System Management > Upgrade and Maintenance > System Software. 2. Click Browse, and select the system software to be uploaded. 3. Click Load to upload the system software to a device, and specify the software as the system software of the device during next-time startup. Restart the device to validate the configuration.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top