RIP configuration method on an AR router

2

The Routing Information Protocol (RIP) is a simple Interior Gateway Protocol (IGP) and based on a distance vector algorithm. RIP measures the distance to the destination network based on the hop count.

For details about the AR router RIP configuration method, see the URL: Example for Configuring RIP.

Other related questions:
SNMP configuration method on an AR router
An AR router supports communication with the NMS over SNMP. SNMP falls into three versions: V1, V2C, and V3. Both V1 and V2C implement access control based on a community name and the MIB view, which poses a security risk. V3 implements access control based on users, user groups, and the MIB view. Security is improved. Therefore, you are advised to use V3. For details, choose Configuration > CLI-based Configuration �?> CLI-based Configuration > SNMP Configuration through the URL: Product Documentation.

Configuring the RIP priority on the firewall
The method for modifying the RIP priority on the USG2000&5000&6000 is as follows: -Modifying the RIP priority: [USG]rip [USG-rip-1]preference 80

Can the RIP protocol on an AR router associate with a one-armed BFD
The RIP protocol on an AR router can associate with a one-armed BFD. For details about the configuration, see the following URL: Example for Configuring One-Arm Static BFD for RIP.

How to configure a route through the web NMS on an AR router
To configure a static route, do as follows: 1. Choose IP Service > Route > Static Route Configuration. . 2. Click Create in the IPv4 Static Route Configuration Table or IPv6 Static Route Configuration Table according to requirements to enter the parameter configuration page. 3. Configure parameters one by one, and click OK to complete the configuration. To configure a dynamic route, do as follows: - Configure the OSPF function. 1. Choose IP Service > Route > Dynamic Route Configuration > OSPF to enter the OSPF List page. 2. Click Create, enter parameters, and click ok to create an OSPF process. 3. On the OSPF List page, select the new OSPF process, click Advanced at the right side, click the Basic or Advanced tab page, and modify the OSPF process parameters according to requirements. - Configure the BGP function. 1. Choose IP Service > Route > Dynamic Route Configuration > BGP, configure parameters, and click Apply. 2. On the Peer Configuration List page, click Create, enter parameters, and click ok to create a BGP neighbor.

How to configure local interface mirroring on AR series routers
By configuring local interface mirroring, you can replicate the packets transmitted through the interface to local monitoring devices for analysis and surveillance. Before configuring local interface mirroring, ensure that the link protocol state of the interface is Up. 1. Configure the local observing interface. Background In local interface mirroring, monitoring devices are directly connected to the observing interface. It is recommended that other configurations should not be performed on an interface that is configured as the observing interface to prevent its mirroring function from being affected: - If not only the mirroring packets but also the packets of other services are transmitted through the observing interface, the source of the packets cannot be distinguished. - If traffic congests on the observing interface, mirroring packets may be discarded because the priority of the mirroring packets is lower. Procedure Run the system-view command to enter the system view. Run the observe-port interface interface-type interface-number command to configure the local observing interface. 2. Configure the local mirroring interface. Background An interface of any type can be configured as a mirroring interface. If an Eth-trunk interface is configured as a mirroring interface, a member interface of the Eth-trunk interface cannot be configured as a mirroring interface separately. If you want to configure a member interface of the Eth-trunk as a mirroring interface, you must unbind the member interface from the Eth-trunk interface. If a member interface of an Eth-trunk is configured as a mirroring interface, the Eth-trunk interface cannot be configured as a mirroring interface. If you want to configure the Eth-trunk interface as a mirroring interface, you must unbind the member interface that is configured as the mirroring interface from the Eth-trunk interface. Procedure Run the system-view command to enter the system view. Run the interface interface-type interface-number command to enter the interface view. Run the mirror to observe-port { both | inbound | outbound } [ exclude-link-head ] command to configure the local mirroring interface.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top