How to delete the network port bonding?

3

1.In the navigation tree of the ISM main interface, choose Clustered NAS Storage System > Device Info.
2.Expand Device Info and select a clustered NAS engine for which a network port bonding is to be deleted.
3.In the function pane, choose Network > Bond Management. The Bond Management dialog box is displayed.
4.Select the network port to be deleted, click Delete. The Warning dialog box is displayed.
5.Select the I have read the warning message carefully and then click OK. The Result dialog box is displayed.
6.Click Close.

Other related questions:
How to delete an observing port on S series switches
For S series switches (except S1700 switches), perform the following configurations to delete an observing port: 1. Delete the binding between the observing port and mirrored port. - Port mirroring [HUAWEI] interface gigabitethernet x/x/x [HUAWEI-GigabitEthernetx/x/x] undo port-mirroring to observe-port x inbound/outbound/both [HUAWEI-GigabitEthernetx/x/x] quit - MQC-based traffic mirroring a. Delete the traffic policy applied to the system, a VLAN, or an interface. In the following example, a traffic policy applied to an interface is deleted. [HUAWEI] interface gigabitethernet x/x/x [HUAWEI-GigabitEthernetx/x/x] undo traffic-policy inbound/outbound [HUAWEI-GigabitEthernetx/x/x] quit b. Delete the traffic policy in the system view. [HUAWEI] undo traffic policy xxx c. Delete the traffic behavior containing the traffic mirroring action in the system view. [HUAWEI] undo traffic behavior xxx - ACL-based traffic mirroring Delete ACL-based traffic mirroring configured in the system or interface view. In the following example, ACL-based traffic mirroring is deleted in the system view. [HUAWEI] interface gigabitethernet x/x/x [HUAWEI-GigabitEthernetx/x/x] undo traffic-mirror inbound acl xxx [HUAWEI-GigabitEthernetx/x/x] quit - VLAN mirroring [HUAWEI] vlan xxx [HUAWEI-vlanxxx] undo mirroring inbound [HUAWEI-vlanxxx] quit - MAC address mirroring [HUAWEI] vlan xxx [HUAWEI-vlanxxx] undo mac-mirroring xxx inbound [HUAWEI-vlanxxx] quit 2. Delete the observing port configuration in the system view. [HUAWEI] undo observe-port x

Delete an observing port from an AR
You can run the undo mirror to observe-port { both | inbound | outbound } command to delete the configuration of port mirroring, and run the undo observe-port interface interface-type interface-number command to delete the observing port.

Delete console port password on s series switch
When you log in to an S series switch (except S1700 switches) through the console port for the first time, the system prompts you to configure a login password. You can use either of the following methods to delete the console port login password: 1. Delete the console port login password on the console user interface. system-view [HUAWEI] user-interface console 0 [HUAWEI-ui-console0] undo authentication-mode Warning: After authentication-mode is deleted, users must configure a new password if users login through the user-interface ui-console0 or configure an authentication mode for current user-interface before next time login. Otherwise, users cannot login. Continue?[Y/N]:y Info: The password was cleared. [HUAWEI-ui-console0] return 2. Delete the console port login password on the BootROM menu. [Note]If a modular switch is used and configured with dual main processing units (MPUs), remove the slave MPU before performing the following operations. After the following operations are complete, install the slave MPU again, and then run the save command to ensure consistent configuration between the two MPUs. On the BootROM menu of the switch, you can clear the console port login password and set a new password after starting the switch. Perform the following operations: a. Connect to the console port of the switch and restart the switch. When the following information is displayed, press Ctrl+B and enter the BootROM password to enter the BootROM main menu: Information displayed on modular switches: Press Ctrl+B to enter boot menu ... 1 Password: //Enter the BootROM password. Information displayed on fixed switches: Press Ctrl+B or Ctrl+E to enter BootROM menu ... 2 password: //Enter the BootROM password. [Note] Some fixed switch models allow you to enter the BootROM main menu by pressing Ctrl+E. Perform operations as prompted. The default BootROM password is as follows: - For fixed S series switches running a version earlier than V100R006C05, the default BootROM password is huawei; for fixed switches running V100R006C05 or a later version, the default BootROM password is Admin@huawei.com. - The default BootROM password for S12700 switches is Admin@huawei.com. For S7700&S9700 series switches running a version earlier than V100R006C00, the default BootROM password is 9300; for S7700&S9700 series switches running V100R006C00 or a later version, the default BootROM password is Admin@huawei.com. b. Select Clear password for console user on the BootROM main menu to clear the password for console port login. c. Select Boot with default mode on the BootROM main menu to start the switch. d. After the switch is started, log in through the console port (authentication is not required), and set a password as prompted after login. e. After you log in to the switch, you can set an authentication mode and password for the console user interface if required.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top