RH2288A V2 noise

2

The data listed in the following is the declared A-weighted sound power levels (LWAd) and declared average bystander position A-weighted sound pressure levels (LpAm) when the server is operating in a 23°C (73.4°F) ambient environment. Noise emissions are measured in accordance with ISO 7999 (ECMA 74) and declared in accordance with ISO 9296 (ECMA 109).
? Idle:
LWAd: 6.0 Bels
LpAm: 44.1 dBA
? Running:
LWAd: 6.8 Bels
LpAm: 52.1 dBA
Note:
The actual sound levels generated when the server is operating vary depending on the server configuration, workload, and ambient temperature.

Other related questions:
Differences between the RH2288 V2, RH2288H V2, and RH2288E
The four NICs of the RH2288 V2 are GE NICs on the mainboard while the NICs of the RH2288H V2 are flexible NICs. The number of PCIe slots on riser cards is also different. The RH2288E V2 supports holding guide rails for installation. For details, see their respective user guide.

Differences among RH1288A V2, RH1288 V2, and RH1288 V3
The differences among the RH1288A V2, RH1288 V2, and RH1288 V3 are listed as follows. The servers' specifications are subject to the official website. ? The RH1288A V2 adopts the Huawei Hi1710 management chip (iBMC), and supports Intel? Xeon? E5-2600 v2 series processors, eight DIMM slots, and two LOM GE electrical ports. ? The RH1288 V2 adopts the management software iMana, and supports Intel? Xeon? E5-2600 and E5-2600 v2 series processors, 24 DIMM slots, and GE or 10GE LOM NIC modules. ? RH1288 V3 adopts the Huawei Hi1710 management chip (iBMC), and supports Intel? Xeon? E5-2600 v3 series processors, 16 DIMM slots, and GE or 10GE LOM NIC modules.

Differences between the 4-socket RH5885 V2 and 8-socket RH5885 V2
An 8-socket RH5885 V2 server is made up of two 4-socket RH5885 V2 servers connected through four QPI cables. One of the 4-socket RH5885 V2 servers serves as the master node and the other as the slave node. Hardware differences: ? Rear I/O module: For the 4-socket server, the rear I/O module can be configured with two hard disks and the QPI cables cannot be connected. For the 8-socket server, the rear I/O module cannot be configured with two hard disks and the QPI cables are required. ? Hard disk quantity: 10 (4-socket server); 16 (8-socket server) ? CPU configuration: The 8-socket server must be configured with all CPUs and the 4-socket server can be configured with two or four CPUs. ? DIMM configuration: For the 4-socket server, DIMMs must be symmetrically installed on the memory risers. For the 8-socket server, apart from the symmetry requirements, the DIMMs must be installed on two nodes and the DIMM configuration must be the same on the two memory risers. ? RAID configuration: The 8-socket server requires only one RAID controller card, which must be installed on the master node. Software differences: ? The slave node of the 8-socket server has no BIOS. Therefore, no BIOS information is displayed on iMana. ? The power button on the front panel of the slave node of the 8-socket server is available, but there is no related power control page on the iMana WebUI. ? The iMana of the slave node of the 8-socket server does not provide black box, power-on strategy, system start strategy, and serial port switchover functions.

Whether the fan noise of the USG6330 can be reduced
You can run the test fan-speed fan-id fan-speed command to adjust the fan speed of the USG6330. Manual adjustment is not recommended.

What do I do when noises occur on RSE6500 recorded video images
Possible Cause: Source and destination bandwidth resources are lower than 4 Mbit/s, and the display screen is greater than 23 inches. Solution: 1)To watch video on a large screen, set recording source and destination resources to 4 Mbit/s when scheduling a conference. 2)Watch the video on a screen smaller than 23 inches.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top