CX911 indicators

0

The CX911 supports the following indicators:
? Power indicator (PWR) (this indicator applies only to the C00 version):
Off: The switch module is not powered on.
Blinking green: The switch module is being powered on.
Steady green: The switch module is operating properly.

? Stacking status indicator (SATA) (this indicator applies only to the C10 version):
Off: The switch module is not powered on.
Blinking green (the first 10 times): The switch module is being powered on.
Blinking green: The switch module is standby in stacking mode and is operating properly.
Steady green: The switch module is active in stacking mode or is not stacked, and is operating properly.

? Health status indicator (HLY):
Off: The switch module is not powered on.
Steady green: The switch module is operating properly.
Blinking red (1 Hz): A major alarm is generated.
Blinking red (4 Hz): A critical alarm is generated.
Blinking red (5 Hz): The switch module is not securely installed.

Offline button/indicator (OFL): currently invalid (reserved)

? Data transmission status indicator for the 10GE optical port:
Off: No data is being transmitted over the port.
Blinking orange: Data is being sent or received over the port.

? Connection status indicator for the 10GE optical port:
Off: The port is not connected or not properly connected.
Steady green: The port is properly connected.

? Data transmission status indicator for the 8G FC optical port (A):
Off: No data is being transmitted over the port.
Blinking orange (twice/second): A high temperature alarm has been generated if the green indicator (L) is blinking twice per second at the same time.
Blinking orange (more than twice/second): Data is being sent or received over the port.

? Connection status indicator for the 8G FC optical port (L):
Off: No optical module is installed, or an exception occurs when the port is receiving optical signals.
Steady green: The port is properly connected.
Blinking green (once/second): The device is registering or the port is in the diagnosis state.
Blinking green (twice/second): The port is not properly connected or the port is faulty. If the orange indicator (A) is blinking twice per second at the same time, a high temperature alarm has been generated.

Other related questions:
Default IP address of CX911 FC
The default IP address of the CX911 FC switching plane is provided below. Other switching planes or BMC is not configured with a default IP address. IP address: 192.168.1.100 Subnet mask: 255.255.255.0 Default gateway: 0.0.0.0

E9000 switch module configuration assistant
Go to Link.

Whether switch modules used on the E9000 are hot-swappable
The E9000 provides four slots to install switch modules. Switch modules in slots 2X and 3X are in a pair, and switch modules in slots 1E and 4E are in a pair. The two switch modules in a pair of slots can operate independently, in 1+1 redundancy mode, or in load sharing mode by working with the OS and NICs.

Whether the CX911 supports GE or 10GE ports
The CX911 supports 10GE optical ports. The ports adapt to GE ports. The supported ports are as follows: ? 10GE switching plane: 32 x 10GE downlink ports (each half-width slot: 2 x 10GE) and 16 x 10GE uplink optical ports ? FC switching plane: 12 x FCoE downlink ports connected to slots 1 to 12, 4 x FC downlink ports connected to slots 13 to 16, and 8 x 8G FC uplink ports

Default user name and password of the CX91x
The default user name and password of the BMC and onboard Ethernet switching plane of the CX91x are as follows: Default user name: root Default password: Huawei12#$ In some cases (such as serial port login and BIOS login), you only need to enter the password but do not need to enter the user name. The default user name and password of the FC switching plane (available only for CX911 and CX912) are as follows: Default user name: admin Default password: Huawei12#$

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top