CX911 performance

2

The network switching performance provided by CX911 of the C00 version is described as follows:
? 10GE switching plane:
Supports 1.28 Tbit/s switching capacity.
Supports the filtering of 1024 MAC addresses.
Supports the capacity of 131072 MAC addresses.
Supports 4094 VLANs.
Supports 9712-byte jumbo frames.
Supports eight priority queues.
? FC switching plane: supports 192 Gbit/s switching capacity.

The network switching performance provided by CX911 of the C10 version is described as follows:
? 10GE switching plane:
Supports 1.28 Tbit/s switching capacity.
Supports a packet forwarding rate of 960 Mpps.
Supports 131072 MAC addresses.
Supports 4063 VLANs.
Supports 128 Eth-Trunk ports (each Eth-Trunk port can be added with a maximum of 16 member ports.)
Supports 16384 ARPs.
Supports 9216-byte jumbo frames.
Each port supports eight queues.
Supports CAR (ingress: 2048; egress: 1024).
Supports 4 MB packet cache.
Supports ACLv4 (pre-ingress: 750; ingress: 1500; egress: 1000).
Supports 128 VRFs (MPLS is not supported).
Supports 16384 VPN routes.
Supports 16384 route entries.
Supports 16384 IPv4 FIBs and 8000 (the mask length is not longer than 64) IPv6 FIBs.
Supports 4000 L3 multicast forwarding entries.
Supports BFD: 128 BFD sessions, and the minimum interval for receiving and sending packets is 50 ms.
Supports VRRP: 64 VRRP backup groups; 64 VRRP management groups; each VRRP backup group supports 16 virtual IP addresses.
Supports a maximum of 48 MSTP instances.
Supports TRILL: 512 network nodes; 4062 CE-VLANs; 16-link load sharing specifications.
? FC switching plane: supports 192 Gbit/s switching capacity.

Other related questions:
Default IP address of CX911 FC
The default IP address of the CX911 FC switching plane is provided below. Other switching planes or BMC is not configured with a default IP address. IP address: 192.168.1.100 Subnet mask: 255.255.255.0 Default gateway: 0.0.0.0

E9000 switch module configuration assistant
Go to Link.

Whether switch modules used on the E9000 are hot-swappable
The E9000 provides four slots to install switch modules. Switch modules in slots 2X and 3X are in a pair, and switch modules in slots 1E and 4E are in a pair. The two switch modules in a pair of slots can operate independently, in 1+1 redundancy mode, or in load sharing mode by working with the OS and NICs.

Whether the CX911 supports GE or 10GE ports
The CX911 supports 10GE optical ports. The ports adapt to GE ports. The supported ports are as follows: ? 10GE switching plane: 32 x 10GE downlink ports (each half-width slot: 2 x 10GE) and 16 x 10GE uplink optical ports ? FC switching plane: 12 x FCoE downlink ports connected to slots 1 to 12, 4 x FC downlink ports connected to slots 13 to 16, and 8 x 8G FC uplink ports

Default user name and password of the CX91x
The default user name and password of the BMC and onboard Ethernet switching plane of the CX91x are as follows: Default user name: root Default password: Huawei12#$ In some cases (such as serial port login and BIOS login), you only need to enter the password but do not need to enter the user name. The default user name and password of the FC switching plane (available only for CX911 and CX912) are as follows: Default user name: admin Default password: Huawei12#$

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top