BH621 V2 hardware

0

CPU

The server blade supports Intel Xeon? new-generation high-performance CPUs. The server blade supports one or two Xeon?E5-2400 (Romley-EN) series high-performance CPUs of 95 W or lower.

Bus

The server blade uses one QuickPath bus for interconnecting CPUs and other components. The bus provides a maximum transmission rate of 8.0 GT/s.
The server blade provides a PCIe x8 slot for a standard full-height half-length PCIe card.

Dual in-line memory module (DIMM)

The server blade provides 12 Double Data Rate 3 (DDR3) slots for installing registered DIMMs (RDIMMS) and load-reduced DIMMs (LRDIMMs). The maximum memory capacity is 192 GB.
The server blade supports the DDR3 memory bus frequency of 800, 1066, 1333, or 1600 MHz.
The server blade supports error checking and correcting (ECC).

Management module

The server blade provides an independent integrate management module (iMana).
The server blade provides redundant Intelligent Platform Management Bus (IPMB) links for connecting to the two MMs.
The server blade provides two 10/100M Ethernet links for connecting to two MMs.

Integrated component

The server blade integrates with a dual-channel gigabit Ethernet (GE) controller (Intel 82580).
The server blade integrates a video graphics array (VGA) (XGI Z11).
if you want to get more information about BH621 V2,please refer to the link:
http://support.huawei.com/enterprise/en/doc/DOC1000009934?idPath=7919749%7C9856522%7C21782478%7C19955021%7C8576270

Other related questions:
Differences between the RH2288 V2, RH2288H V2, and RH2288E
The four NICs of the RH2288 V2 are GE NICs on the mainboard while the NICs of the RH2288H V2 are flexible NICs. The number of PCIe slots on riser cards is also different. The RH2288E V2 supports holding guide rails for installation. For details, see their respective user guide.

Differences among RH1288A V2, RH1288 V2, and RH1288 V3
The differences among the RH1288A V2, RH1288 V2, and RH1288 V3 are listed as follows. The servers' specifications are subject to the official website. ? The RH1288A V2 adopts the Huawei Hi1710 management chip (iBMC), and supports Intel? Xeon? E5-2600 v2 series processors, eight DIMM slots, and two LOM GE electrical ports. ? The RH1288 V2 adopts the management software iMana, and supports Intel? Xeon? E5-2600 and E5-2600 v2 series processors, 24 DIMM slots, and GE or 10GE LOM NIC modules. ? RH1288 V3 adopts the Huawei Hi1710 management chip (iBMC), and supports Intel? Xeon? E5-2600 v3 series processors, 16 DIMM slots, and GE or 10GE LOM NIC modules.

Differences between the 4-socket RH5885 V2 and 8-socket RH5885 V2
An 8-socket RH5885 V2 server is made up of two 4-socket RH5885 V2 servers connected through four QPI cables. One of the 4-socket RH5885 V2 servers serves as the master node and the other as the slave node. Hardware differences: ? Rear I/O module: For the 4-socket server, the rear I/O module can be configured with two hard disks and the QPI cables cannot be connected. For the 8-socket server, the rear I/O module cannot be configured with two hard disks and the QPI cables are required. ? Hard disk quantity: 10 (4-socket server); 16 (8-socket server) ? CPU configuration: The 8-socket server must be configured with all CPUs and the 4-socket server can be configured with two or four CPUs. ? DIMM configuration: For the 4-socket server, DIMMs must be symmetrically installed on the memory risers. For the 8-socket server, apart from the symmetry requirements, the DIMMs must be installed on two nodes and the DIMM configuration must be the same on the two memory risers. ? RAID configuration: The 8-socket server requires only one RAID controller card, which must be installed on the master node. Software differences: ? The slave node of the 8-socket server has no BIOS. Therefore, no BIOS information is displayed on iMana. ? The power button on the front panel of the slave node of the 8-socket server is available, but there is no related power control page on the iMana WebUI. ? The iMana of the slave node of the 8-socket server does not provide black box, power-on strategy, system start strategy, and serial port switchover functions.

What are the SMC2.0 hardware and software specifications and what is the background system?
To obtain the introduction to the SMC2.0 hardware and software specifications and background system, perform the following operations: 1. Log in to Huawei Enterprise Technical Support Website. 2. Search for SMC2.0. 3. Select the version number to obtain the product documentation. 4. Check the corresponding product description chapter in the product documentation.

Hardware parameters of S series switches
For the hardware description of the S5700, see S5700 Hardware Description. For the hardware description of the S6700, see S6700 Hardware Description. For the hardware description of the S600, see S600 Hardware Description. For the hardware description of the S9300 and S9300E, see S9300&S9300E Hardware Description. For the hardware description of the S7700, see S7700 Hardware Description. For the hardware description of the S9700, see S9700 Hardware Description. For the hardware description of the S12700, see S12700 Hardware Description.

If you have more questions, you can seek help from following ways:
To iKnow To Live Chat
Scroll to top