Configure svf port from trunk to access

Abdussamed · Created Jun 27, 2021 19:12:11

Example for Configuring SVF

Networking Requirements

A new campus network has a large number of wired and wireless access devices. The widely distributed access devices complicate management and configuration of the access layer. Unified management and configuration of wired and wireless access devices are required to reduce the management cost.

In Figure 10-25, the parent is directly connected to a level-1 AS, and the level-1 AS is directly connected to an AP. The PC's network port is directly connected to the parent's Ethernet management port for a login to the web system to configure SVF.

This configuration example uses the S5720HI as the parent, an S5700-10P-PWR-LI-AC as the level-1 AS, and an AP4030DN as the AP. Both the parent and level-1 AS use the software version V200R010C00, and the AP uses the software version V200R007C10.

Figure 10-25 SVF networking
download?uuid=8e01e602b26747649662b6444849e34c

Configuration Roadmap

The configuration roadmap is as follows:

Log in to the web system of the parent through the PC and ensure that the PC and parent reside on the same network segment.
Change to the SVF mode.
Configure the SVF system capability.

Enable SVF and configure the management VLAN ID and management IP address.
Add the level-AS.
Add the AP.

Clear the AS configuration and restart it to ensure that this unconfigured AS can be connected to the SVF system. Connect the level-1 AS to the parent and connect the AP to the level-1 AS using cables.

Check whether the SVF configuration is correct.

Data Plan

Item	Data
MAC addresses of the parent, AS1 and AP1	Parent: 0500-0000-XXXX AS1: 88cf-98ba-XXXX AP1: fcb6-98d6-XXXX
SVF management VLAN	VLAN 4090
IP address of the management VLANIF	192.168.2.1
Port that connects the parent to AS1	GE0/0/1
Port that connects the AS1 to parent	GE0/0/9 NOTE: If the AS needs to use downlink service ports as member ports of the connected uplink fabric port, you need to run the command to specify these downlink service ports as member ports of the connected uplink fabric port. For details, see Configuring an AS in "SVF Configuration" in the S1720, S2700, S5700, and S6720 V200R011C10 Configuration Guide - Device Management.
Port that connects AS1 to AP1	GE0/0/8
AP SN	21500826412SF690XXXX

Procedure

Log in to the web system of the parent through the PC.
1. Open the web browser on the PC, enter https://management address of the parent in the address box, and press Enter. The web system login page is displayed, as shown in Figure 10-26.
  
  Figure 10-26 Web system login page
2. Select a language English for the web system.
3. Enter the configured web user name and password, and click GO or press Enter. The web system page is displayed.
Change to the SVF mode.
1. Click in the upper left corner of the web system page, as shown in Figure 10-27.
  
  Figure 10-27 Changing to the SVF Mode
2. In the dialog box that is displayed, click OK, as shown in Figure 10-28.
  
  The system automatically redirects you to the SVF Enabling page.
  Figure 10-28 Confirming the switchover to the SVF mode
Enable the SVF function on the parent.

Set Management VLAN ID to 4090.
Set Management network scale to 512.
Set Management IP address/mask to 192.168.2.1/255.255.254.0.
Set AS access authentication to OFF.
Set AP access authentication to Non-auhtentication.

Set Enable SVF to ON. The SVF Enabling page is displayed, as shown in Figure 10-29.

Perform the following configurations:
Figure 10-29 Enabling SVF
Click Apply. In the dialog box that is displayed, click OK, as shown in Figure 10-30.

Figure 10-30 Confirming the enabling of the SVF function

When an operation success message is displayed, click OK.

Add AS1.

Choose Configuration > SVF Quick Config > AS Addition and click the Configure AS Fabric-Ports tab.
Click Create and set AS Fabric-Port Resides On to Parent and AS Fabric-Port ID to 0, as shown in Figure 10-31.

Figure 10-31 Configuring AS fabric-ports (AS1)
Click Select Ports in Fabric-Port Member Ports. In the displayed Add Port dialog box, select GE0/0/1 (the port connected to AS1) as the fabric-port, and click OK, as shown in Figure 10-32.

Figure 10-32 Adding ports (AS1)
Choose Centralized mode for AS Configuration Mode. After the configurations are complete, click .
Click the Manage ASs tab.
Click Create, as shown in Figure 10-33.

Figure 10-33 Naming ASs (AS1)
Set AS Name to as1 and AS Management MAC to 88cf-98ba-XXXX.
Click Manage below AS Model. The Manage AS Model dialog box is displayed, as shown in Figure 10-34. Set Product series to S5700-10P-LI, AS model to S5700-10P-PWR-LI-AC, and AS stacking to OFF, and click OK.

Figure 10-34 Managing the AS model
After the configurations are complete, click .

Add AP1.

Set Creation mode to Manually add.
Set Keyword to AP MAC.
Set AP MAC to fcb6-98d6-XXXX.
Set AP ID to 1.
Set AP type to AP4030DN.
Set AP SN to 21500826412SF690XXXX.

Choose Configuration > SVF Quick Config > AP Addition and click the Configure Ports Connected to APs tab. Select as1 from AS Name, as shown in Figure 10-35.

Figure 10-35 Configuring the port connected to the AP
Click Add Selected and select GE0/0/8 from the displayed Manage as1 Member User Ports dialog box, as shown in Figure 10-36.

Figure 10-36 Managing member ports of AS1
Click OK to finish configuring the port connecting AS1 to AP1.
Click the Configure APs tab, click Create to set AP parameters, and click OK after setting these parameters, as shown in Figure 10-37.

Perform the following configurations:
Figure 10-37 Creating an AP

Log in to the AS using a command, run the reset saved-configuration command to clear the AS configuration, and reboot the AS. If the system asks you whether to save the current configuration during the reboot, enter N. Connect the level-1 AS to the parent and connect the AP to the level-1 AS using cables.

Result

After configuring SVF, perform the following operations to verify the configurations:

Choose Monitoring > Summary. In the displayed page, you can view SVF overview and device status information. Click on the left side of Member Device Status, and you can view that both the AS and AP are online, as shown in Figure 10-38. This indicates that an SVF system has been set up.
Figure 10-38 SVF overview
Check the SVF topology.

Choose Monitoring > Topology. The SVF topology page is displayed. You can view the level-1 AS topology, as shown in Figure 10-39.
Figure 10-39 Level-1 AS topology
Click the AS1 and AP1 icons. You can view detailed information about AS1 and AP1, as shown in Figure 10-40 and Figure 10-41.
Figure 10-40 AS1 detailed information

Figure 10-41 AP1 detailed information

More information-->

https://support.huawei.com/enterprise/en/doc/EDOC1000169679/5ca843cd/example-for-configuring-svf

Hope it can help you.

Abdussamed · Created Jun 27, 2021 19:09:20

Thanks for contacting the Huawei community!

We are checking your question and will provide an answer to you shortly...

Abdussamed · Created Jun 27, 2021 19:12:11

Example for Configuring SVF

Networking Requirements

A new campus network has a large number of wired and wireless access devices. The widely distributed access devices complicate management and configuration of the access layer. Unified management and configuration of wired and wireless access devices are required to reduce the management cost.

In Figure 10-25, the parent is directly connected to a level-1 AS, and the level-1 AS is directly connected to an AP. The PC's network port is directly connected to the parent's Ethernet management port for a login to the web system to configure SVF.

This configuration example uses the S5720HI as the parent, an S5700-10P-PWR-LI-AC as the level-1 AS, and an AP4030DN as the AP. Both the parent and level-1 AS use the software version V200R010C00, and the AP uses the software version V200R007C10.

Figure 10-25 SVF networking
download?uuid=8e01e602b26747649662b6444849e34c

Configuration Roadmap

The configuration roadmap is as follows:

Log in to the web system of the parent through the PC and ensure that the PC and parent reside on the same network segment.
Change to the SVF mode.
Configure the SVF system capability.

Enable SVF and configure the management VLAN ID and management IP address.
Add the level-AS.
Add the AP.

Clear the AS configuration and restart it to ensure that this unconfigured AS can be connected to the SVF system. Connect the level-1 AS to the parent and connect the AP to the level-1 AS using cables.

Check whether the SVF configuration is correct.

Data Plan

Item	Data
MAC addresses of the parent, AS1 and AP1	Parent: 0500-0000-XXXX AS1: 88cf-98ba-XXXX AP1: fcb6-98d6-XXXX
SVF management VLAN	VLAN 4090
IP address of the management VLANIF	192.168.2.1
Port that connects the parent to AS1	GE0/0/1
Port that connects the AS1 to parent	GE0/0/9 NOTE: If the AS needs to use downlink service ports as member ports of the connected uplink fabric port, you need to run the command to specify these downlink service ports as member ports of the connected uplink fabric port. For details, see Configuring an AS in "SVF Configuration" in the S1720, S2700, S5700, and S6720 V200R011C10 Configuration Guide - Device Management.
Port that connects AS1 to AP1	GE0/0/8
AP SN	21500826412SF690XXXX

Procedure

Log in to the web system of the parent through the PC.
1. Open the web browser on the PC, enter https://management address of the parent in the address box, and press Enter. The web system login page is displayed, as shown in Figure 10-26.
  
  Figure 10-26 Web system login page
2. Select a language English for the web system.
3. Enter the configured web user name and password, and click GO or press Enter. The web system page is displayed.
Change to the SVF mode.
1. Click in the upper left corner of the web system page, as shown in Figure 10-27.
  
  Figure 10-27 Changing to the SVF Mode
2. In the dialog box that is displayed, click OK, as shown in Figure 10-28.
  
  The system automatically redirects you to the SVF Enabling page.
  Figure 10-28 Confirming the switchover to the SVF mode
Enable the SVF function on the parent.

Set Management VLAN ID to 4090.
Set Management network scale to 512.
Set Management IP address/mask to 192.168.2.1/255.255.254.0.
Set AS access authentication to OFF.
Set AP access authentication to Non-auhtentication.

Set Enable SVF to ON. The SVF Enabling page is displayed, as shown in Figure 10-29.

Perform the following configurations:
Figure 10-29 Enabling SVF
Click Apply. In the dialog box that is displayed, click OK, as shown in Figure 10-30.

Figure 10-30 Confirming the enabling of the SVF function

When an operation success message is displayed, click OK.

Add AS1.

Choose Configuration > SVF Quick Config > AS Addition and click the Configure AS Fabric-Ports tab.
Click Create and set AS Fabric-Port Resides On to Parent and AS Fabric-Port ID to 0, as shown in Figure 10-31.

Figure 10-31 Configuring AS fabric-ports (AS1)
Click Select Ports in Fabric-Port Member Ports. In the displayed Add Port dialog box, select GE0/0/1 (the port connected to AS1) as the fabric-port, and click OK, as shown in Figure 10-32.

Figure 10-32 Adding ports (AS1)
Choose Centralized mode for AS Configuration Mode. After the configurations are complete, click .
Click the Manage ASs tab.
Click Create, as shown in Figure 10-33.

Figure 10-33 Naming ASs (AS1)
Set AS Name to as1 and AS Management MAC to 88cf-98ba-XXXX.
Click Manage below AS Model. The Manage AS Model dialog box is displayed, as shown in Figure 10-34. Set Product series to S5700-10P-LI, AS model to S5700-10P-PWR-LI-AC, and AS stacking to OFF, and click OK.

Figure 10-34 Managing the AS model
After the configurations are complete, click .

Add AP1.

Set Creation mode to Manually add.
Set Keyword to AP MAC.
Set AP MAC to fcb6-98d6-XXXX.
Set AP ID to 1.
Set AP type to AP4030DN.
Set AP SN to 21500826412SF690XXXX.

Choose Configuration > SVF Quick Config > AP Addition and click the Configure Ports Connected to APs tab. Select as1 from AS Name, as shown in Figure 10-35.

Figure 10-35 Configuring the port connected to the AP
Click Add Selected and select GE0/0/8 from the displayed Manage as1 Member User Ports dialog box, as shown in Figure 10-36.

Figure 10-36 Managing member ports of AS1
Click OK to finish configuring the port connecting AS1 to AP1.
Click the Configure APs tab, click Create to set AP parameters, and click OK after setting these parameters, as shown in Figure 10-37.

Perform the following configurations:
Figure 10-37 Creating an AP

Log in to the AS using a command, run the reset saved-configuration command to clear the AS configuration, and reboot the AS. If the system asks you whether to save the current configuration during the reboot, enter N. Connect the level-1 AS to the parent and connect the AP to the level-1 AS using cables.

Result

After configuring SVF, perform the following operations to verify the configurations:

Choose Monitoring > Summary. In the displayed page, you can view SVF overview and device status information. Click on the left side of Member Device Status, and you can view that both the AS and AP are online, as shown in Figure 10-38. This indicates that an SVF system has been set up.
Figure 10-38 SVF overview
Check the SVF topology.

Choose Monitoring > Topology. The SVF topology page is displayed. You can view the level-1 AS topology, as shown in Figure 10-39.
Figure 10-39 Level-1 AS topology
Click the AS1 and AP1 icons. You can view detailed information about AS1 and AP1, as shown in Figure 10-40 and Figure 10-41.
Figure 10-40 AS1 detailed information

Figure 10-41 AP1 detailed information

More information-->

https://support.huawei.com/enterprise/en/doc/EDOC1000169679/5ca843cd/example-for-configuring-svf

Hope it can help you.

user_3642052 · Created Jun 28, 2021 05:18:09

Not clear how to change port mode from trunk to access
Because i need to conect cisco switche to as switch

chenhui · Created Jun 28, 2021 05:59:57

Posted by user_3642052 at 2021-06-28 05:18 Not clear how to change port mode from trunk to access Because i need to conect cisco switche to as ...

Hello,
I'm not sure what you the 'as switch', if you mean you want to configure the SVF switch interface from trunk to access, please refer to the command below:
interface G0/0/1
port link-type access
port default vlan xx

Notice: In an SVF system, parent switches are identified and managed using their stack member IDs, and leaf switches are identified and managed using their leaf IDs. Therefore, interfaces on a parent switch are numbered in the format member stack ID/subcard ID/interface number, and interfaces on a leaf switch are numbered in the format leaf ID/subcard ID/interface number.

andersoncf1 · Created Jun 28, 2021 17:40:54

Good answer

Configure svf port from trunk to access

Recommended answer

Example for Configuring SVF

Networking Requirements

Configuration Roadmap

Data Plan

Procedure

Result

Example for Configuring SVF

Networking Requirements

Configuration Roadmap

Data Plan

Procedure

Result

Third Party’s Trade Secret

My Followers

Enterprise

Consumer

Corporate

Carriers

Configure svf port from trunk to access

Recommended answer

Example for Configuring SVF

Networking Requirements

Configuration Roadmap

Data Plan

Procedure

Result

Example for Configuring SVF

Networking Requirements

Configuration Roadmap

Data Plan

Procedure

Result

Third Party’s Trade Secret

My Followers