Change inverter rs485 baud rate from SmartLogger 3000

BetterMing · Created Feb 24, 2021 00:55:58

Hello, dear.
The baud rate is a communication parameter, which is generally set when the equipment is installed on the network. If Smartlogger3000 communicates with the inverter normally, it means that the baud rate of the inverter is the same as that of the Smartlogger device. If you modify the baud rate of Smartlogger, it will not be able to communicate with all inverters normally. So you only have to modify the baud rate of the inverter on the inverter and modify the baud rate of the interface in smartlogger.

ariase88 · Created Feb 23, 2021 16:19:30

Thanks for contacting the Huawei community!

We are checking your question and will provide an answer to you shortly...

BetterMing · Created Feb 24, 2021 00:55:58

Hello, dear.
The baud rate is a communication parameter, which is generally set when the equipment is installed on the network. If Smartlogger3000 communicates with the inverter normally, it means that the baud rate of the inverter is the same as that of the Smartlogger device. If you modify the baud rate of Smartlogger, it will not be able to communicate with all inverters normally. So you only have to modify the baud rate of the inverter on the inverter and modify the baud rate of the interface in smartlogger.

A.Angelov · Created Feb 24, 2021 05:23:54

Yes i know that,
The question is:
I have 600 inverters comunicationg with 15 Smartloggers with baud rate 9600.
Now they want to put the baudrate to 19200. Is there a way to set this rate to te inverters i batch remotely.
Or i have to go to evry one and set the speed by connecting to it by phone and app.

BetterMing · Created Feb 25, 2021 06:04:27

You can check again

Setting RS485 Communications Parameters

Set RS485 parameters and click Submit.

Figure 6-13 Setting RS485 parameters
download?uuid=bbacd3b65c284f21b1b4f287dd14fe30

download?uuid=c421a2c0ce8943fda479606fc007bf64

When the SmartModule is connected to the SmartLogger, the device name of the SmartModule is Module(M1), and the corresponding port is M1.COM.

RS485

Protocol, Baud rate, Parity, and Stop Bit must be set to the same values for the devices connected to the same COM port.

Parameter	Description
Protocol	Set this parameter based on the protocol type of the connected device. The value can be Modbus, IEC103, DL/T645, Modbus-Slave, or Modbus-Control. NOTE: When the SmartLogger serves as a slave node to interconnect with a third-party device over Modbus-RTU, set Protocol to Modbus-Slave. When the connected solar inverter performs rapid power grid scheduling using both MBUS and RS485, set Protocol to Modbus-Control.
Baud rate	Set this parameter based on the baud rate of the connected device. The value can be 1200, 2400, 4800, 9600, 19200, or 115200.
Parity	Set this parameter based on the parity mode of the connected device. The value can be None, Odd parity, or Even parity.
Stop Bit	Set this parameter based on the stop bit of the connected device. The value can be 1 or 2.
Start address	1 ≤ Start address ≤ Communication address of the connected device ≤ End address ≤ 247 The address segments of COM ports can overlap. NOTE: The start and end addresses have no impact on the devices that have been connected.
End address

Change inverter rs485 baud rate from SmartLogger 3000

Best answer

Recommended answer

Setting RS485 Communications Parameters

RS485

Third Party’s Trade Secret

My Followers

Enterprise

Consumer

Corporate

Carriers

Change inverter rs485 baud rate from SmartLogger 3000

Best answer

Recommended answer

Setting RS485 Communications Parameters

RS485

Third Party’s Trade Secret

My Followers