You can refer to the following information:
Remove Interface IP Address (RMV IFIP)Network Element: BTS3900, BTS3900 WCDMA, BTS3900 LTE, BTS3900 5G, BTS5900, BTS5900 WCDMA, BTS5900 LTE, BTS5900 5G FunctionUse this command to remove an interface IP address from a port. NoteThis is a high-risk MML command. Pay attention to the following precautions before running this command: This command is used to remove only the interface IP address that is added by running the ADD IFIP command. The added interface IP addresses can be listed by running the LST IFIP command. The operation will interrupt the services or OM channels carried on the interface IP address. You are advised to run the CFM CB command to enable configuration data rollback. [NodeB,eNodeB,gNodeB]You cannot remove an interface IP address used by a link such as a remote maintenance channel or BFD session.
Parameters| ID | Name | Description |
|---|
| CN | Cabinet No. | Meaning: Indicates the cabinet number of the board where the port is located. Disuse statement: This parameter will be deleted in later versions. In the current version, this parameter can be configured and takes effect when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to OLD, and this parameter cannot be configured and is replaced by the Interface ID parameter in the IPADDR4 MO when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to NEW. Therefore, avoid using this parameter. GUI Value Range: 0~7 Unit: None Actual Value Range: 0~7 MML Default Value: 0 Recommended Value: 0 Parameter Relationship: None Service Interrupted After Modification: N/A Impact on Radio Network Performance: None Applicable Mode: G, U, L, N, R | | SRN | Subrack No. | Meaning: Indicates the subrack number of the board where the port is located. Disuse statement: This parameter will be deleted in later versions. In the current version, this parameter can be configured and takes effect when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to OLD, and this parameter cannot be configured and is replaced by the Interface ID parameter in the IPADDR4 MO when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to NEW. Therefore, avoid using this parameter. GUI Value Range: 0~1 Unit: None Actual Value Range: 0~1 MML Default Value: 0 Recommended Value: 0 Parameter Relationship: None Service Interrupted After Modification: N/A Impact on Radio Network Performance: None Applicable Mode: G, U, L, N, R | | SN | Slot No. | Meaning: Indicates the slot number of the board where the port is located. Disuse statement: This parameter will be deleted in later versions. In the current version, this parameter can be configured and takes effect when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to OLD, and this parameter cannot be configured and is replaced by the Interface ID parameter in the IPADDR4 MO when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to NEW. Therefore, avoid using this parameter. GUI Value Range: 0~7 Unit: None Actual Value Range: 0~7 MML Default Value: None Recommended Value: None Parameter Relationship: None Service Interrupted After Modification: N/A Impact on Radio Network Performance: None Applicable Mode: G, U, L, N, R | | SBT | Subboard Type | Meaning: Indicates the type of sub-board on the board where a port is located. Disuse statement: This parameter will be deleted in later versions. In the current version, this parameter can be configured and takes effect when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to OLD, and this parameter cannot be configured and is replaced by the Interface ID parameter in the IPADDR4 MO when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to NEW. Therefore, avoid using this parameter. GUI Value Range: E1_COVERBOARD(E1 Cover Board), ETH_COVERBOARD(Ethernet Cover Board), BASE_BOARD(Base Board), BACK_BOARD(Back Board) Unit: None Actual Value Range: E1_COVERBOARD, ETH_COVERBOARD, BASE_BOARD, BACK_BOARD MML Default Value: None Recommended Value: None Parameter Relationship: -Others: [Co-MPT, NodeB, eGBTS, eNodeB, gNodeB]In an IFIP MO, this parameter can be set to E1_COVERBOARD or ETH_COVERBOARD if SN is set to a value within the range of 0 to 5. In an IFIP MO, this parameter can be set to BASE_BOARD, BACK_BOARD, or ETH_COVERBOARD if SN is set to 6 or 7.
Service Interrupted After Modification: N/A Impact on Radio Network Performance: None Applicable Mode: G, U, L, N, R | | PT | Port Type | Meaning: Indicates the type of the physical port. The UMTS currently does not support SUBIF. Disuse statement: This parameter will be deleted in later versions. In the current version, this parameter can be configured and takes effect when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to OLD, and this parameter cannot be configured and is replaced by the Interface ID parameter in the IPADDR4 MO when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to NEW. Therefore, avoid using this parameter. GUI Value Range: PPP(PPP Link), MPGRP(Multi-link PPP Group), ETH(Ethernet Port), ETHTRK(Ethernet Trunk), SUBIF(Sub-interface), ETHCI(Ethernet CI Port) Unit: None Actual Value Range: PPP, MPGRP, ETH, ETHTRK, SUBIF, ETHCI MML Default Value: None Recommended Value: None Parameter Relationship: -Configuration constraints: [Co-MPT, NodeB, eGBTS, eNodeB, gNodeB]In the IFIP MO, if PT is not set to SUBIF, VRFIDX must be set to 0. [gNodeB]The value of PT in an IFIP MO cannot be set to MPGRP. [gNodeB]The value of PT in an IFIP MO cannot be set to PPP. [gNodeB]The value of PT in an IFIP MO cannot be set to ETHCI.
-Others: [Co-MPT, NodeB, eGBTS, eNodeB, gNodeB]In the IFIP MO, if SBT is set to BASE_BOARD, this parameter can be set to PPP, MPGRP, ETH, ETHTRK, SUBIF, or ETHCI. In the IFIP MO, if SBT is set to BACK_BOARD, this parameter must be set to PPP. In the IFIP MO, if SBT is set to E1_COVERBOARD, this parameter can be set to PPP or MPGRP. In the IFIP MO, if SBT is set to ETH_COVERBOARD, this parameter can be set to ETH or ETHTRK.
Service Interrupted After Modification: N/A Impact on Radio Network Performance: None Applicable Mode: G, U, L, N, R | | PN | Port No. | Meaning: Indicates the number of a port. Disuse statement: This parameter will be deleted in later versions. In the current version, this parameter can be configured and takes effect when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to OLD, and this parameter cannot be configured and is replaced by the Interface ID parameter in the IPADDR4 MO when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to NEW. Therefore, avoid using this parameter. GUI Value Range: 0~63 Unit: None Actual Value Range: 0~63 MML Default Value: None Recommended Value: None Parameter Relationship: -Others: [Co-MPT, NodeB, eGBTS, eNodeB, gNodeB]In the IFIP MO, this parameter can be set to a value within the range of 0 to 15 if SBT is set to BACK_BOARD and PT is set to PPP. In the IFIP MO, this parameter can be set to a value within the range of 0 to 15 if SBT is set to BASE_BOARD or E1_COVERBOARD and PT is set to PPP. In an IFIP MO, this parameter can be set to a value within the range of 0 to 3 if SBT is set to BASE_BOARD and PT is set to ETH. In an IFIP MO, this parameter can be set to 0 or 1 if SBT is set to BASE_BOARD and PT is set to ETHTRK. In an IFIP MO, this parameter can be set to a value within the range of 0 to 3 if PT is set to MPGRP. In an IFIP MO, this parameter can be set to a value within the range of 0 to 5 if SBT is set to ETH_COVERBOARD and PT is set to ETH. In an IFIP MO, this parameter can be set to a value within the range of 0 to 2 if SBT is set to ETH_COVERBOARD and PT is set to ETHTRK. In an IFIP MO, this parameter can be set to a value within the range of 0 to 63 if PT is set to SUBIF. In an IFIP MO, this parameter can be set to 0 if PT is set to ETHCI.
Service Interrupted After Modification: N/A Impact on Radio Network Performance: None Applicable Mode: G, U, L, N, R | | VRFIDX | VRF Index | Meaning: Indicates the index of a VRF instance. UMTS currently supports the default routing domain only (the VRF index is 0). Disuse statement: This parameter will be deleted in later versions. In the current version, this parameter can be configured and takes effect when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to OLD, and this parameter cannot be configured and is replaced by the VRF Index parameter in the IPADDR4 MO when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to NEW. Therefore, avoid using this parameter. GUI Value Range: 0~7 Unit: None Actual Value Range: 0~7 MML Default Value: 0 Recommended Value: 0 Parameter Relationship: -Configuration constraints: [Co-MPT, NodeB, eGBTS, eNodeB, gNodeB]In the IFIP MO, if PT is not set to SUBIF, VRFIDX must be set to 0.
Service Interrupted After Modification: N/A Impact on Radio Network Performance: None Applicable Mode: G, U, L, N, R | | IP | IP Address | Meaning: Indicates the IP address configured for the port. Disuse statement: This parameter will be deleted in later versions. In the current version, this parameter can be configured and takes effect when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to OLD, and this parameter cannot be configured and is replaced by the IP parameter in the IPADDR4 MO when the Transmission Configuration Mode parameter in the GTRANSPARA MO is set to NEW. Therefore, avoid using this parameter. GUI Value Range: Valid IP address Unit: None Actual Value Range: Valid IP address MML Default Value: None Recommended Value: None Parameter Relationship: -Configuration constraints: [Co-MPT, NodeB, eGBTS, eNodeB, gNodeB]IP in the IFIP MO must be set to a valid IP address of Class A, B, or C. In addition, it cannot be 127.x.x.x or 0.x.x.x. [Co-MPT, NodeB, eGBTS, eNodeB, gNodeB]In the logical operation result of IP and MASK in an IFIP MO, neither the network ID nor host ID can be all 0 or 1 after being converted into a binary value.
Service Interrupted After Modification: N/A Impact on Radio Network Performance: None Applicable Mode: G, U, L, N, R |
ExampleExample 1: To remove an interface IP address with the parameters as follows: Cabinet No.: 0, Subrack No.: 0, Slot No.: 6, Subboard Type: BASE_BOARD, Port Type: ETH, Port No.: 0, IP Address: 192.168.2.24, run the following command:
RMV IFIP: CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PT=ETH, PN=0, IP="192.168.2.24";
Example 2: To remove an interface IP address with the parameters as follows: Cabinet No.: 0, Subrack No.: 0, Slot No.: 1, Subboard Type: E1_COVERBOARD, Port Type: MPGRP, Port No.: 1, IP Address: 192.168.11.23, run the following command:
RMV IFIP: CN=0, SRN=0, SN=1, SBT=E1_COVERBOARD, PT=MPGRP, PN=1, IP="192.168.11.23";
|
