Got it
Huawei Enterprise Support Community
Community Forums Routing & Switching
AR515GW + IP Camera

AR515GW + IP Camera

Created: Jan 10, 2017 18:20:05Latest reply: Nov 8, 2018 10:41:47 2141 6 1 0 0
  Rewarded HiCoins： 10 (problem resolved)
View the author 1#

Hi friends! 

I have some problems trying to configure a router AR515GW in order to connect with an IP Camera, I know how to configure IP Cameras through conventional procedures using the Port Forwarding, but with this router, I have tried several procedures but I can't get the task done. I would like to know if you can support me with this issue, so what's the correct procedure to add N-IP Cameras to the router, thanks! 


Like (1) Dislike (0) Favorite(0) Share Report
Previous: [CASE]After configuring ipsec vpn on router,ping is normal but telnet is abnormal
Next: Can't get B593 router to recognize external antenna.
Featured Answers

Recommended answer

(0) (0)
No.9527
Created Nov 8, 2018 10:41:47

This post was last edited by No.9527 at 2018-11-15 02:57.

Configuring Basic Parameters for Communication Between the Device and Front-End Processor

1. Run the system-view command to enter the system view.

  1. 2. Run the ami command to enter the AMI view.
  2. 3. Run the basic heart-interval interval-value command to set the heartbeat interval.

    By default, the heartbeat interval is 5 minutes.

  3. 4. Run the basic report-retry retry-num command to set the maximum number of retries when the device reports heartbeat packets to register with a front-end processor.

    By default, the maximum number of report retries is 3.  

Configuring Connection Type

  1. Run the system-view command to enter the system view.
  2. Run the ami command to enter the AMI view.
  3. Run the connection connection-name command to configure a connection name and enter the connection view.
  4. Run the parameter protocol-type { iec62056 | modbus } command to set the communication protocol type of a front-end processor connecting to the device.
  5. Run the parameter connection-type tcp-client { remote address port port-num | time-out time | retry-wait interval-value } *command to set the local connection type, remote IP address, remote port number, and timeout period and interval of the connection with the remote end on the device.
  6. (Optional) Run the set net timeout time-value command to set the timeout period of the Ethernet data request between the device and front-end processors. By default, the timeout period of Ethernet data requests is 30s.

Configuring the Authentication Level

  1. Run the system-view command to enter the system view.
  2. Run the ami command to enter the AMI view.
  3. Run the basic authorization-level level command to configure the authentication for front-end processors.

    By default, the authentication level of communication between the device and a front-end processor is high-level authentication. There are also non-authentication and low-level authentication.

  4. Run the basic id id password { low | high } command to configure the device ID and low-level authentication or high-level authentication password.

    • When high-level authentication is used, specify high and configure the device ID and authentication password.

    • When low-level authentication is used, specify low and configure the device ID and authentication password.

    • When no authentication is used, specify low or high and configure the device ID.

  5. (Optional) When the authentication level is high-level authentication, run the basic high-algorithm { aes-128 | sha-256 } command to configure the encryption algorithm for high-level authentication.

    By default, high-level authentication uses the SHA-256 algorithm.

View more

This article contains more resources

You need to log in to download or view. No account? Register

x
  • x
  • convention：
All Answers
(0) (0)
2#
user_2790689
user_2790689 Created Jan 11, 2017 01:06:10

ding
View more
  • x
  • convention：
(0) (0)
3#
Busy_with_lazy_mind
Busy_with_lazy_mind Created Jan 11, 2017 06:54:32

Could you tell me which project you are working at? Maybe I can ask someone to give you technical support.You can send a mail to wangxiuwen1@huawei.com
View more

Rating

Number of participants 1 +5 Collapse Reasons
Lemon Lemon + 5 赞一个

View All scores

  • x
  • convention：
(0) (0)
4#
AntonioGonz
AntonioGonz Created Jan 13, 2017 16:19:40

Posted by 过于走心选择困难 at 2017-01-11 06:54 Could you tell me which project you are working at? Maybe I can ask someone to give you technical su ...
Smart Bus Solution, I need to get some devices working together, 2 IP Cameras, 1 Inteligent passenger counter, 2 panic bottons, prepaid card reader (RFID), so I would like to know how to do the integration with te AR515GW. Recently I have installed an OS (Linux SUSE) in the router and I need to get the device port access between router (WiFi, LTE, GPS, WAN/LAN Ports, ...) and the OS installed inside.
View more
  • x
  • convention：
(0) (0)
5#
Skay
Skay Created Oct 24, 2018 06:43:06

hi AntonioGonz ， you can contract to me , i am good at this model device and configured some of them .
View more
  • x
  • convention：
(0) (0)
6#
chenhui
chenhui Admin Created Nov 6, 2018 07:03:15


@AntonioGonz plz describe your problem more precisely
View more
  • x
  • convention：
(0) (0)
7#
No.9527
No.9527 Created Nov 8, 2018 10:41:47

This post was last edited by No.9527 at 2018-11-15 02:57.

Configuring Basic Parameters for Communication Between the Device and Front-End Processor

1. Run the system-view command to enter the system view.

  1. 2. Run the ami command to enter the AMI view.
  2. 3. Run the basic heart-interval interval-value command to set the heartbeat interval.

    By default, the heartbeat interval is 5 minutes.

  3. 4. Run the basic report-retry retry-num command to set the maximum number of retries when the device reports heartbeat packets to register with a front-end processor.

    By default, the maximum number of report retries is 3.  

Configuring Connection Type

  1. Run the system-view command to enter the system view.
  2. Run the ami command to enter the AMI view.
  3. Run the connection connection-name command to configure a connection name and enter the connection view.
  4. Run the parameter protocol-type { iec62056 | modbus } command to set the communication protocol type of a front-end processor connecting to the device.
  5. Run the parameter connection-type tcp-client { remote address port port-num | time-out time | retry-wait interval-value } *command to set the local connection type, remote IP address, remote port number, and timeout period and interval of the connection with the remote end on the device.
  6. (Optional) Run the set net timeout time-value command to set the timeout period of the Ethernet data request between the device and front-end processors. By default, the timeout period of Ethernet data requests is 30s.

Configuring the Authentication Level

  1. Run the system-view command to enter the system view.
  2. Run the ami command to enter the AMI view.
  3. Run the basic authorization-level level command to configure the authentication for front-end processors.

    By default, the authentication level of communication between the device and a front-end processor is high-level authentication. There are also non-authentication and low-level authentication.

  4. Run the basic id id password { low | high } command to configure the device ID and low-level authentication or high-level authentication password.

    • When high-level authentication is used, specify high and configure the device ID and authentication password.

    • When low-level authentication is used, specify low and configure the device ID and authentication password.

    • When no authentication is used, specify low or high and configure the device ID.

  5. (Optional) When the authentication level is high-level authentication, run the basic high-algorithm { aes-128 | sha-256 } command to configure the encryption algorithm for high-level authentication.

    By default, high-level authentication uses the SHA-256 algorithm.

View more

This article contains more resources

You need to log in to download or view. No account? Register

x
  • x
  • convention：
Back to list

Comment

Advanced
B Color Image Link Quote Code Smilies
You need to log in to comment to the post Login | Register
Comment

Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " User Agreement."

My Followers

Login and enjoy all the member benefits

Login
Huawei Website Support About Huawei Privacy User Agreement Terms of Use Cookies Cookie Settings
Huawei Enterprise Huawei Carrier Forum Training & Certification

Contact Us: e_online@huawei.com Copyright © 2022 Huawei Technologies Co., Ltd. All rights reserved.

APP

Block
Are you sure to block this user?
Users on your blacklist cannot comment on your post,cannot mention you, cannot send you private messages.
Reminder
Please bind your phone number to obtain invitation bonus.