Hi everyone!
This is a small, basic article about configuring the Wi-Fi 6 AP-5760-10 model. Please see below for more details.
LOGIN
This login mode is applicable to Fat APs.
Before logging in to an AP through the web platform, connect a terminal to the AP using an Ethernet cable or in wireless mode to ensure that they are connected to each other. Then you can log in to the AP using a browser
SSID: HUAWEI-LeaderAP-XXXX XXXX specifies the last four digits of the AP's MAC address.
Password: hw_manage
Wired IP: 169.254.1.1
Wireless:192.168.1.1
Password: admin@huawei.com
CONNECTING TO THE AP
Through an Ethernet cable
You can connect a PC to any network port on an AP or to a network port on a switch reachable to the AP (the IP addresses of the PC and AP on the same network segment).
1. Use an Ethernet cable to connect the PC to the AP.
2. Configure the PC.
LOGGING IN TO A Fat AP
Configure the PC to automatically obtain an IP address.
In wireless mode
Connecting to an AP in wireless mode
1. Configure the terminal to automatically obtain an IP address.
2. Within the coverage of the AP, search for the WLAN on the terminal. You can access the WLAN directly or by entering the correct wireless password.
LOGGING IN TO THE AP
1. Open the browser on the PC, enter http://IP address or https://IP address in the address box and press Enter. The login page is displayed.
2. Enter the login information.
a) Select a language.
b) The system supports English and Chinese. By default, the system uses the same language as the browser.
c) Enter a username and password.
d) Click Login.
e) To ensure the security of the web platform, you are prompted to change the password upon the first login and log in to the web platform again.
3. Click Logout in the upper right corner to log out of the web platform. The login page is displayed.
4. If you do not perform any operation within a specified duration (10 minutes by default), you are logged out. To return to the login page, click OK.
MONITORING
Internet: choose Monitoring > Summary. Check the Internet area.
User: choose Monitoring > Summary. Check the User area.
Access Point: choose Monitoring > Summary. Check the Access Point area.
View details: choose Monitoring > Summary > View Details. Check the Device Information area on the View Details tab page.
Uplink configuration: choose Configuration > Internet Configuration. The Uplink network interface Configuration page is displayed.
SSID configuration
Management SSID:
1. Choose Configuration > WLAN Configuration.
Click the SSID in the management SSID list. The Management SSID page is displayed.
2. Enter the details and click Apply. (SSID, Password, Rate Limit).
System configuration
Choose Configuration > System Configuration > Basic Config. The Basic Config page is displayed.
Radio calibration
Configuring an automatic radio calibration
1. Choose Configuration > System Configuration > Radio Calibration. The Radio Calibration page is displayed.
2. Enable Calibration.
3. Set Triggering condition as Auto and specify the Calibration start time and Calibration interval (minutes).
4. Configure parameters as required.
5. Click Apply.
Configuring a scheduled radio calibration
1. Choose Configuration > System Configuration > Radio Calibration. The Radio Calibration page is displayed.
2. Enable Calibration.
3. Set Triggering condition as Scheduled and specify the Calibration start time and Select time range.
4. Configure parameters as required.
5. Click Apply.
Configuring a manual radio calibration.
1. Choose Configuration > System Configuration > Radio Calibration. The Radio Calibration page is displayed.
2. Enable Calibration.
3. Set Triggering condition as Manual and configure parameters as required.
4. Click Apply.
DIAGNOSIS TOOL
One-Click Information Collection
1. Choose Maintenance > Diagnosis Tool > One-click Information Collection. The One-click Information Collection page is displayed.
2. Click on the information to be collected and click Collect. In the dialog box that is displayed, click OK.
3. When the collection is complete, a dialog box is displayed. Click OK.
PING
1. Choose Maintenance > Diagnosis Tool > Ping. The Ping page is displayed.
2. Set the IP address/host name to be pinged.
3. Click Start.
TRACE ROUTE
1. Choose Maintenance > Diagnosis Tool > Trace Route. The Trace Route page is displayed.
2. Set the IP address/hostname to be traced.
3. Click Start.
RADIO ENVIRONMENT DETECTION
1. Choose Maintenance > Diagnosis Tool > Radio Environment Detection. The Radio Environment Detection page is displayed.
2. Configure parameters as required.
3. Click Apply. The test result for the air interface environment is displayed.
ADMINISTRATOR
1. Choose Maintenance > Administrator > Administrator. The Administrator page is displayed.
2. In the Administrator List area, click Create. On the Create Administrator page that is displayed, configure parameters as required.
PASSWORD POLICY
1. Choose Maintenance > Administrator > Administrator. The Administrator page is displayed.
2. In the Password Policy area, configure parameters as required.
DEVICE RESTART
Choose Maintenance > Device Restart. The Restart page is displayed.
FILE MANAGEMENT
1. Choose Maintenance > System > File Management. The File Management page is displayed.
2. Check the total and available spaces of the flash memory on top of the page.
3. Manage all files on the flash memory in the File List area.
Select a file and click Delete. The file is deleted to the recycle bin. You can recover the file in the Recycle Bin area.
Select a file and click Completely Delete. The device is deleted from the device and cannot be recovered.
Click Upload and upload a file to the flash memory.
Select a file and click Download or ↓ to download the file from the flash memory to the local PC.
Recover all files from the recycle bin in the Recycle Bin area.
Select a file and click Restore File to recover the file to the original storage device.
Select a file and click Completely Delete. The device is deleted from the device and cannot be recovered.
Thanks 
