The tag of ospf peer impact ospf routing learning.

Created Dec 29, 2018 10:49:35Latest reply Dec 31, 2018 22:36:12 420 7 7 0
Check   ospf peer on CE, if the  tag for the   peer is 1.  Checking on the PE, the tag   for this ospf peer should be 1 too. If OSPF VPN multi-instance is deployed on   a Multi-VPN-Instance CE (MCE), routes cannot be calculated based on Type3,   Type5, or Type7 LSAs with the DN bit. Therefore, OSPF detects routing loops   when calculating routes.
    ======================================================
   
 
===============display ospf   brief===============
    ======================================================
   
    OSPF Process 1 with Router ID x.x.x.x
   
         
OSPF Protocol   Information
   
    RouterID: x.x.x.x
    Border   Router:  AREA 
AS
 
ECA-route-type: 0x0306
    Route Tag: 0
   
 
PE Router, Multi-VPN-Instance is   enabled
    Global DS-TE Mode: Non-Standard IETF Mode
    Graceful-restart capability: disabled
    Helper support capability
 
: not   configured
    Spf-schedule-interval: max 10000ms, start 500ms, hold 1000ms
    Default ASE parameters: Metric: 1 Tag: 1 Type: 2
    Route Preference: 10
   
 
ASE Route Preference: 150
 
SPF Computation Count: 4
   
    Solution for the issue is that add command vpn-instance-capability simple
 
on CE router.
    #
    ospf 1 router-id x.x.x.x vpn-instance test
    import-route direct
    vpn-instance-capability simple
    area 0.0.0.1
   
 
network y.y.y.y 0.0.0.3
    #
    If OSPF VPN multi-instance is deployed on a Multi-VPN-Instance CE (MCE),   routes cannot be calculated based on Type3, Type5, or Type7 LSAs with the DN   bit. Therefore, OSPF detects routing loops when calculating routes. In this   case, the vpn-instance-capability simple command is used to disable OSPF   routing loop detection and enable OSPF to calculate routes based on received   LSAs without checking the DN bit and route-tag in the LSAs. The route-tag is   restored to the default value 1.

  • x
  • convention:

SupperRobin  Novice   Created Dec 29, 2018 11:21:48 Helpful(0) Helpful(0)

If OSPF VPN multi-instance is deployed on a Multi-VPN-Instance CE (MCE), routes cannot be calculated based on Type3, Type5, or Type7 LSAs with the DN bit. Therefore, OSPF detects routing loops when calculating routes. In this case, the vpn-instance-capability simple command is used to disable OSPF routing loop detection and enable OSPF to calculate routes based on received LSAs without checking the DN bit and route-tag in the LSAs. The route-tag is restored to the default value 1.
  • x
  • convention:

Finn92  Novice   Created Dec 29, 2018 11:41:32 Helpful(0) Helpful(0)

Check ospf peer on CE, if the tag for the peer is 1. Checking on the PE, the tag for this ospf peer should be 1 too. If OSPF VPN multi-instance is deployed on a Multi-VPN-Instance CE (MCE), routes cannot be calculated based on Type3, Type5, or Type7 LSAs with the DN bit. Therefore, OSPF detects routing loops when calculating routes.
  • x
  • convention:

yjhd     Created Dec 29, 2018 13:41:16 Helpful(0) Helpful(0)

If OSPF VPN multi-instance is deployed on a Multi-VPN-Instance CE (MCE), routes cannot be calculated based on Type3, Type5, or Type7 LSAs with the DN bit. Therefore, OSPF detects routing loops when calculating routes. In this case, the vpn-instance-capability simple command is used to disable OSPF routing loop detection and enable OSPF to calculate routes based on received LSAs without checking the DN bit and route-tag in the LSAs. The route-tag is restored to the default value 1.
  • x
  • convention:

yiyi0519  Novice   Created Dec 29, 2018 13:50:18 Helpful(0) Helpful(0)

OSPF-TE is an extension to OSPF extending the expressivity to allow for traffic engineering and use on non-IP networks.[21] Using OSPF-TE, more information about the topology can be exchanged using opaque LSA carrying type-length-value elements. These extensions allow OSPF-TE to run completely out of band of the data plane network. This means that it can also be used on non-IP networks, such as optical networks.

OSPF-TE is used in GMPLS networks as a means to describe the topology over which GMPLS paths can be established. GMPLS uses its own path setup and forwarding protocols, once it has the full network map.

In the Resource Reservation Protocol (RSVP), OSPF-TE is used for recording and flooding RSVP signaled bandwidth reservations for label switched paths within the link-state database.
  • x
  • convention:

NoOneNoWhere  Adept   Created Dec 29, 2018 14:58:14 Helpful(0) Helpful(0)

The title is "The tag of ospf peer impact ospf routing learning", but actually you shared us is just part of the ospf process and router ID, could you tell us more details about how ospf working on huawei Cloud engine switches.
  • x
  • convention:

littlestone     Created Dec 29, 2018 19:07:22 Helpful(0) Helpful(0)

OSPF routing protocol is a link-state routing protocol for Internet Protocol (IP) networks. The protocol uses the internal gateway protocol (IGP) of link state routing algorithm.
  • x
  • convention:

w1  Moderator   Created Dec 31, 2018 22:36:12 Helpful(0) Helpful(0)

Thanks for your sharing, normally, the OSPF is a very important protocol and very common, so the logs are also very important for checking the issue of OSPF, this post is very good for us to understand the logs, thanks again
  • x
  • convention:

Responses

Reply
You need to log in to reply to the post Login | Register

Notice:To ensure the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but not limited to politically sensitive content, content concerning pornography, gambling, drug abuse and trafficking, content that may disclose or infringe upon others' intellectual properties, including commercial secrets, trade marks, copyrights, and patents, and personal privacy. Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see“ Privacy Policy.”
If the attachment button is not available, update the Adobe Flash Player to the latest version!
Fast reply Scroll to top