Establishing an IPSec Tunnel Through Negotiation Initiated by AR with a Dynamic IP Address to C3900e (Using the Host Name) Highlighted

Created: Feb 25, 2017 09:34:09Latest reply: Feb 25, 2017 13:48:17 1633 1 0 0

Specifications

This example applies to all versions and routers.

This example applies to routers of all versions.

Networking Requirements

As shown in Figure 1-4, RouterA is the enterprise branch gateway, the public network interface dynamically obtains an IP address, and RouterB is the enterprise headquarters gateway (Cisco router). The branch and headquarters communicate through the public network.

The enterprise wants to protect data flows between the branch subnet and the headquarters subnet. Because the branch gateway dynamically obtains an IP address, the headquarters gateway can use the host name to establish an IPSec tunnel with the branch gateway.

Figure 1-1 Networking for establishing an IPSec tunnel through negotiation initiated by the branch gateway with a dynamic IP address to the headquarters Cisco router

20170225093400432001.png

 

Procedure

                      Step 1    Configure RouterA.

note

MD5, SHA-1, DES, and 3DES have potential security risks. Exercise caution when you use them.

The commands used to configure IKE peers and the IKE protocol differ depending on the software version.

l  In earlier versions of V200R008:

ike peer peer-name [ v1 | v2 ]

l  In V200R008 and later versions:

l  To configure IKE peers: ike peer peer-name

l  To configure the IKE protocol: version { 1 | 2 }

By default, IKEv1 and IKEv2 are enabled simultaneously. An initiator uses IKEv2 to initiate a negotiation request, while a responder uses IKEv1 or IKEv2 to respond. To initiate a negotiation request using IKEv1, run the undo version 2 command.

#
 sysname RouterA  //Configure the device name.
#
 ipsec authentication sha2 compatible enable
#
 ike local-name huawei
#
acl number 3000  //Specify data flows (traffic from the branch subnet to the headquarters subnet) to be protected.
 rule 5 permit ip source 10.1.1.0 0.0.0.255 destination 10.1.2.0 0.0.0.255
#
ipsec proposal prop1  //Configure an IPSec proposal.
 esp authentication-algorithm sha2-256
 esp encryption-algorithm aes-128
#
ike proposal 1  //Configure an IKE proposal.
 encryption-algorithm aes-cbc-128   //In V200R008 and later versions, the aes-cbc-128 parameter is changed to aes-128.
 dh group14
 authentication-algorithm sha2-256
#
ike peer peer1 v1  //Configure an IKE peer.
 exchange-mode aggressive  //Configure the aggressive mode.
 pre-shared-key cipher %@%@W'KwGZ8`tQ8s^C8q(qC"0(;@%@%@%#%#@W4p8i~Mm5sn;9Xc&U#(cJC;.CE|qCD#jAH&/#nR%#%#  //Configure the pre-shared key as huawei@1234.
 ike-proposal 1
 local-id-type name   //Set the local ID type in IKE negotiation to name.
 remote-name RouterB
 remote-address 60.1.2.1  
#
ipsec policy policy1 10 isakmp  //Configure an IPSec policy.
 security acl 3000 
 ike-peer peer1
 proposal prop1
#
interface GigabitEthernet0/0/1
 ipsec policy policy1     //Apply the IPSec policy to the interface.
 ip address dhcp-alloc    //Enable the DHCP client function to allow the branch gateway to dynamically obtain an IP address. In addition, you also need to configure the DHCP 
                            server function on the device directly connected or having a reachable route to RouterA. For detailed configurations, see the product documentation
                            of the device used.
#
interface GigabitEthernet0/0/2
 ip address 10.1.1.1 255.255.255.0
#
return

                      Step 2    Configure RouterB.

!
hostname RouterB  //Configure the device name.
!
crypto isakmp policy 1
 encryption aes 128
 hash sha256
 authentication pre-share
 group 14
crypto isakmp key huawei@1234 hostname huawei  //Configure the pre-shared key as huawei@1234.
!
crypto isakmp identity hostname   //Set the local ID type in IKE negotiation to hostname.
!
crypto ipsec transform-set p1 esp-sha256-hmac esp-aes 128  //Configure a security algorithm used by IPSec.
!
!
crypto dynamic-map p1 1  //Create a dynamic crypto map entry.
 set transform-set p1
 match address 102

!
crypto map p1 1 ipsec-isakmp dynamic p1  //Configure an IPSec policy.
!
!
interface GigabitEthernet0/0
 ip address 60.1.2.1 255.255.255.0
 duplex auto
 speed auto
 crypto map p1     //Apply the IPSec policy to the interface.
!
interface GigabitEthernet0/1
 ip address 10.1.2.1 255.255.255.0
 duplex auto
 speed auto
!
!
ip route 0.0.0.0 0.0.0.0 60.1.2.2  //Configure a static route to ensure reachability at both ends.
!
access-list 102 permit ip 10.1.2.0 0.0.0.255 10.1.1.0 0.0.0.255 //Specify data flows (traffic from the headquarters subnet to the branch subnet) to be protected.
!
end

                      Step 3    Verify the configuration.

# After the configuration is complete, run the ping command on PC A. PC B can be pinged.

# Run the display ike sa and display ipsec sa commands on RouterA, and run the show crypto isakmp sa and show crypto ipsec sa commands on RouterB. You can see that the IPSec tunnel is created successfully.

# Run the display ipsec statistics command on RouterA to check data packet statistics.

----End

Configuration Notes

In this example, the commands on the Cisco router are recommended ones. The product version is Cisco IOS Software, C3900e Software (C3900e-UNIVERSALK9-M), Version 15.2(4)M1, RELEASE SOFTWARE (fc1). For details, visit http://www.cisco.com/cisco/web/support.

 

This post was last edited by 关关系列 at 2017-02-28 10:17.
  • x
  • convention:

gululu     Created Feb 25, 2017 13:48:17 Helpful(0) Helpful(0)

thanks!
  • x
  • convention:

Come on!

Reply

Reply
You need to log in to reply to the post Login | Register

Notice: To protect the legitimate rights and interests of you, the community, and third parties, do not release content that may bring legal risks to all parties, including but are not limited to the following:
  • Politically sensitive content
  • Content concerning pornography, gambling, and drug abuse
  • Content that may disclose or infringe upon others ' commercial secrets, intellectual properties, including trade marks, copyrights, and patents, and personal privacy
Do not share your account and password with others. All operations performed using your account will be regarded as your own actions and all consequences arising therefrom will be borne by you. For details, see " Privacy."
If the attachment button is not available, update the Adobe Flash Player to the latest version!
Fast reply Scroll to top